Fisters' fans, every year, becomes more and more. Newbies, who only comprehend this kind of catch, face a lot of problems, one of which is the choice of the rod. In this article, let's talk to what parameters, first of all, it is worth paying attention to.
The length of the feeder rod varies from 2.7 to 4.8 m., With a knee step 0.3 m. The choice of stick on this parameter depends: from the casting of the cast and the intended trophy. If you are going to catch on a small river or lake, where copies rarely exceed 500 grams, then the feeder, a length of 3.3 m., It will be enough. On reservoirs and rivers, more than 100 meters wide, rods are needed - 3.6 - 3.9 m. With a strong course, four-meter blanks are used, which, after throwing, are installed in a vertical position in order not to check the fishing line and better control the snap. Some models of rods complete have an extra knee.
Each feeder rod has two or five multi-colored replaceable vertices, or quivertips. They act as a pilot warning device and have their test, or rigidity, which is measured in ounces (OZ) or grams (G), 1 oz - 28 grams. With the right choice of feeding feeders, the snap has an angle of quivertipa 90 degrees. Also, the test can be determined by color:
1. Hard quiverrtip red. Used with a strong course for trophy fish.
2. Middle quivertype of yellow. They put on the blanks at the rustling and wind weather.
3. Soft green quivertip. Designed for catching in standing water and instances up to 500-600 grams.
Make quivertips from materials such as fiberglass, carbon fiber and combined materials.
Thinks from carbon fiber are considered the best. They have excellent rigidity and low weight. It is comfortable to catch with them on the reservoirs with standing water, and on rivers with a rapid flow. But they are more expensive than the rest.
Quivertips from fiberglass won in the price of the first, but inferior in quality. They are very fragile and even a small load can lead it into disrepair, also should not forget that when interacting with water, they are resolve.
For a beginner, the most suitable, there will be combined vertexes. They absorbed all the advantages of the quiverrtips from the first two materials. The rod is made of fiberglass, it makes it sensitive, and the commute part is wrapped with a carbon fiber, which increases the rigidity of the quiverrtip.
This parameter means what maximum weight feeder can withstand the form. If you put the load less than indicated on the rod, it will lose in sensitivity, and it can break it large.
Ultralight "Ultra Light", also called Picker. The blank length does not exceed three meters. Test 10-40 grams. Designed for catching in standing water.
Light "Light". Blanca length 3-3.6 meters. Test 40-80 grams. You can already catch with him where it will be impossible to fish with a picker. You can throw the snap to 40 meters.
Middle "Medium". Length of a form 3.6-3.9 meters. Test 80-100 grams. Range of cast - 50 meters.
Heavy "Heavy". Length of 3.6-4 meters blank. Test 100-120 grams. Perfectly suitable for fishing on a rapid flow.
Super heavy "Extra Heavy". The length of the blank from 4 meters and above. Test up to 300 grams. Such forms are used to throw at a very long distance, as well as for catching large instances.
By the rank of forms there are three types:
1. Slow. With a rusty of such a building, you need to handle carefully, as it is very flexible. Light feeders put on it and catch in standing water or on a river with a weak flow. When quenching, the load is distributed throughout the Blanch: from Komel to the tip.
2. Fast. Such blanks have excellent stiffness. Only 1/3 rods are bent when the top is bent: the top and the first knee. Catching with such a rod allows you to better control the snap.
3. Complex, or "parabolic system". When loading, the form bends in the increasing: from the vertex to the komel. There are such rods expensive.
High-modern graphite (carbon) . Such form enjoy experienced feeders. They require careful care, as very fragile. Rods from such material light, durable, have a good margin of strength and rigidity. It is not necessary to allow sand, small pebbles and dirt in the place of the knee connection, as in the future it will lead to its breakdown. Another minus of such a stick is a big price, compared with forms from other materials.
Composite . An excellent solution for those who are only mastering feeder fishing. By weight, it is heavier stick from carbon. The advantages of a rod of composite material: excellent stiffness, are not demanding of the care and the price of them is significantly less than on forms from high-modulus graphite.
Fiberglass . Use with a strong course and for catching large instances. Fiberglass forms are the toughest and heavy, as well as they are cheaper than the rest of the rods.
Telescopic and plug rods
Telescopic blanks are more suitable for beginners. In the assembled state, they occupy little space and you can not be afraid to break them, which is convenient during transportation. Of the minuses you can allocate: the lack of strengthening materials in the locations of the knees, which poorly affects the block of the form; Limited test range up to 80 grams, as well as difficulty in repairing them.
Plug forms use experienced fishermen. Pluses: the ability to extinguish large fish jerks due to uniform loads throughout the forms; The plug rod allows you to make a more accurate and distant cast. Cons: In the disassembled state, they have a length of about a meter, which is not convenient when transporting, compared with telescopic rods; High price, and also hard to repair.
The more bandwidth rings on the feeder rod, the better. The rings mount can be divided into two types: on two and three legs. The first option is found on Chinese fakes and cheap blanks of fiberglass. It is better not worth buying a rod with such a fastening, since the rings can cuddle to the rod and quickly come into disrepair. The second option is found in composite and high-modern graphite blanks. Rings on them have inserts from metal-ceramics with coating of silicon carbide, titanium nitride and aluminum oxide, which allows the use of braided cord, unlike the first.
Summing up can be said that the choice of feeder rod is not a simple matter, especially for the beginner. Only after fully studying all the nuances and figure out in all subtleties, it is possible to appreciate this kind of catching.
Thank you very much to everyone who finished my article to the end, I hope you liked it. I would be grateful to you for the like and subscription to the channel. Thank you. Thank you !!! Waiting on the channel !!!
In stores a very wide selection of fishing accessories and accessories, which sometimes makes even experienced fishermen. Feeder rods were also not ignored. The range of various manufacturers, prices and characteristics will confuse knowledgeable fishermen, which is already talking about newcomers.
The first thing is to be guided by the selection of rods - the conditions of fishing. Before you go to the store, you need to know about the strength of the flow in the reservoir, its depth and preferential range of the bottom, as well as take into account the species composition of the underwater inhabitants. The newcomer will have to choose one rod, and experienced fishermen have about 10 models in their drawer, oriented under various fishing conditions.
What is a feeder rod?
For bottom fishing there are a lot of diverse gears, but it is feeder rods that are considered the most effective and frequently used. Large and sweaty feeders, which are used in the equipment contribute to the rapid delivery of bait in the bottom layers, and feeder equipment allow you to fish in pleasure.
The essential difference between such rods from the usual spinning lies in removable vertices, which are responsible for the role of the bone alarm and the relatively large number of rings (there may be about 20 pieces). Materials manufacturing are used as for other blanks.
In the literal translation from English feeder means nothing else like a feeder . In the eighties, the idea of such a snap came to mind one of the craftsmen. And this method of fishing quickly gained popularity among fishermen, having received a huge amount of improvements.
British fishermen very quickly adapted to such snaps and immediately found the use for such a row of gear. After British fishermen evaluated the effectiveness of the use of this kind of gear, their popularity increased sharply.
The small distance between the bait and hook with a bait is a great advantage of similar gears. During repeated casts, the bait gradually falls out of the feeders and part of it remains at the bottom, additionally attracting fish. And the large weight of the feeder only contributes to spontaneous cutting of the fish.
How to choose a feeder rod
Before buying a feeder rod, you need to clarify some uncomplicated, but very important nuances. If you buy a rod for the first time, then you better buy an inexpensive and universal model . As the experience set, the fisherman will be able to independently make requirements for the rod.
If you are planning to fish In places with a strong current at large distances , it will be necessary to choose a rod of a large length with a corresponding test. Also Do not forget about the size of the expected production . For catching a crucian on the feeder in the pond you will not need rough tackle, but for catching carp you need to take the rod tougher.
It is important and taking into account the frequency of departure on the reservoir and the number of hours that you plan to spend on fishing. Buy an expensive rod when you go fishing no more than 5 times per season will be just meaningless spending money . If you are an avid fisherman, which almost all free time spends on fishing, then you can apply a professional rod.
Feeder rods can be characterized by a large number of different readings :
- Length of the rod;
- removable vertex;
- Test feeder rod;
- Blow rings.
The length of modern models of rods for fishing on the feeder can be from 2.7 to 4.8 meters, manufacturers make a step in length of 30 centimeters. Less frequently, the manufacturers of English models can have a different length.
Most often, domestic fishermen use feeder rods whose length is from 3.6 to 3.9 meters. Such rods make it possible to send tool on a large distance and are considered an optimal solution for fishing in our reservoirs.
They also have excellent characteristics that are able to provide complete control over the snap-in. If you plan to throw feeder snaps to an impressive distance, then you will need to buy a blank length more than 4 meters.
Rods whose length ranges from 4.2 to 4.8 meters oriented for fishing in places at high flow rate. Such fishing rods should be installed vertically on the shore of the reservoir to reduce the length of the fishing line lying in the water.
Some models are supplied complete with additional knees, the use of which allows you to significantly increase their length. It is very convenient, since by paying for one rod you can use it for fishing from the boat and from the shore at the same time.
QUIVERTIP (KVIVERTIP) - removable vertex
Each model of the rod, which does not relate to cheap, is completed with 3-4 removable vertices from synthetic material. Fiberglass or carbonate vershs are painted in bright colors, as they will play the role of the feeder bleclock signal and should be well visible.
Toppers are playing the role of the shock absorber when digging the fish, and are also tuning signaling devices.
Such verses have different stiffness. Typically, such indications are indicated in ounces, this is done in order to pay tribute to the British. OUTION is 28.35 grams . This indicator is determined by hanging loaded to the rod versa, the cargo fixation is performed when the tip is bent at an angle of 90 degrees. The label is applied to the form itself and it can be three types:
- For fishing On the reservoirs at a low flow of current or without it, soft verses are suitable without it . Most often, such models are made of fiberglass, as it has great flexibility than other materials.
- Middle Stiffness Tips Apply to windy weather or for catching in water bodies with an average flow rate.
- Conglastic rigid vershicles Apply for fishing in places with a strong flow.
The vertex is not a continuation of the rod and does not particularly affect its characteristics. During the cast, this part of the form is experiencing minimum loads. Their destination is a reaction to bite and nothing more. Each fisherman puts forward individual requirements for the alarm, so the selection of the vertex should be made individually.
Test feeder rod
There are no universal rods, each model is intended for fishing in specific conditions. For the selection of the optimal characteristics of the fishing rods on its form, there is an inscription that is responsible for the right weight of the cargo for throwing (sometimes instead of the inscriptions the word is indicated).
- Equipment whose weight does not exceed 30 grams You can throw a rod of the LIGHT class;
- Feeders weighing up to 60 grams Better to throw the medium-light class with the rod;
- MEDIUM rods are designed to pass the gear from 60 to 80 grams ;
- MEDIUM-Heavy rod class means that it is optimal for fishing with tackles weighing 80 to 100 grams ;
- HEAVY feeder rods allow an fisherman to throw tackle weighing from 100 to 120 g ;
- Heavy models of Extra-Heavy class provide comfortable fishing on the equipment weighing Over 120 grams .
Observe the test feeder rod necessarily. If you take a feeder with a smaller mass, then it can negatively affect the sensitivity of the vertex. The use of feeders of a larger mass can entail a breakdown of the rod during the cast.
The feeder rod building is also a very important characteristic and directly affects the choice of a particular model:
- Quick Stroy It is able to provide long-range tractions tackle and quick cutting of fish. Under the load deforms the first knee and the peak of the rod. Retribute large fish with such a rod is very difficult, so you will need a certain experience.
- Slow Stroy Provides casts to the middle distance. Under the load deforms the entire rod, with the exception of the handle. Such a fishing rod is able to extinguish a large fish jerk, so that newcomers will be the best option.
- Inexpensive feeder rods have Progressive Stroy . These rods are called parabolic, as their flexion depends on the load force.
In the manufacture of rods, the materials used are a very important factor. It is from the materials used that the main characteristics of the form will depend on the price of a rod. Most often manufacturers use such materials during production:
- carbon fiber;
- Composite materials (different combination of previous materials).
Each material in its Persons and gives the rod of those or other characteristics that the fisherman can be guided during the model selection:
- Crawly . This is a modern material, but despite all the innovation he has some shortcomings. Crawling rods are very much. Yes, and the blanks of their such material are very fragile and gentle, so they require special care and relationships. Such models are manufactured for experienced fishermen.
- Composite materials . These are inexpensive rods that are the perfect choice for beginners. The material has greater weight and increased rigidity, but it is durable.
- Fiberglass . These rods are used by fishermen when it is required to throw the snap-in for a large distance or fishing occurs in places with a large flow, as an example of carp fishing per feeder will not do without using such a fishing rod.
Grooming rings on the rod
Blow rings deserve separate attention. Many fishermen do not pay due attention to the rings when buying a rod, which then regret. After a certain period, it can be noted that the casting becomes more difficult, and the fishing line can be to wear.
Many fishermen begin to boldly assure everyone that these are wine producer. And the reason is immediately becoming an experienced fishermen, they only need to look at bandwidth rings. If the quality of the bandwidth rings is low, they will quickly fail by wiping through the fishing line.
Material from which bandwidth rings must necessarily be sufficiently high quality. Feeder rods are constantly loadable to loads and wear is subject to absolutely all models, but the time of failure directly depends on the material of the manufacture of the rings.
Fastening the rings to the Blanc of the rod is also a very important point. Prefer the models with three legs on the rings. All fishermen say that Fuji rings, Balzer is best. They are made with inserts from various materials, such as titanium, silicon or china.
Feeder rod rating
With how to choose a feeder rod, we figured out, now it's time to move to specifics. What are the best feeder rods and which manufacturers are preferable to give an advantage when choosing and buying a rod?
Especially in order to answer all these questions by our version, it was decided to draw up a feeder rod rating. Budgetary and expensive blanks are involved in the ranking, so each fisherman can choose a suitable model.
Models of rod kaida
Kaida is a very popular manufacturer who supplies the domestic market predominantly budget models. Three models from this manufacturer deserve special attention, as they are inexpensive, and quality is at a high level.
- Feeder Fishing Kaida Spirado Feeder 330 , having a test to 150 grams. The price of this model is $ 18, which is very cheap (though, in some stores a line of such rods is an order of magnitude more expensive). The characteristics with which this fishing rod is suitable to any novice fisherman. The form weighs only 350 grams, its length is 3.3 meters, and it can be challenged to 150 grams. There is a modification, a long 3.9 meter, which is more expensive than this model.
- Model of the rod KAIDA ALBATRON FEEDER XH 3.60 meters long with a dough from 30 to 120 grams also deserves attention. This fishing rod costs $ 35, but it is made of carbon and much easier than the previous one (only 265 grams). The package includes 4 removable vertexes.
- KAIDA TELE BIG FISH FEEDER 330 The test range of which ranges from 60 to 120 grams is perfectly suitable for fishing on the carp using feeder gears. The price of such a rod is about 35 dollars and it has a telescopic structure.
Feedher rods Salmo.
Salmo feeder rods have proven themselves among Russian fishermen as one of the most reliable rods in the domestic market. The price of Salmo rod models can be from 50 to 200 dollars. Some fishermen note that the forms are easily resistant, but it is caused by improperly transport and storage, but not bad quality.
The best female feeders are presented in the domestic market:
- Rod Salmo Taifun. - its price is about 15 dollars;
- Fishing rod Salmo Elite. - the price of the model is 35 dollars;
- Model of the rod Salmo Supreme. - costs about 16 dollars;
- Feeder Salmo Diamond. - for this rod will have to give 30 dollars;
Fishing rods Mikado.
The rods from the manufacturer Mikado belongs to the average price category, so they have found no significant popularity as previous models. The cheapest models of such fishing are about 15 dollars.
- Feeder rod Mikado Golden Lion Ultrafeeder 3.3 meter long made of composite material, has an average system and completed with additional removable vertices in the amount of 3 pieces. The mass of such a rod is about 300 grams, and the price is about $ 19.
- Model of the rod Mikado X-Plode Medium Feeder The length of which is 3.6 meters made of carbon fiber and has a decent set of characteristics. The price of the model is 70 dollars.
Rods from MiFine will be an excellent choice for beginners who are comprehended by feeder fishing. Prices on the rod models of this manufacturer will be pocket to all fishermen, and their quality fully matches the spent money.
- Feeder Fishing Mifine Hulk Feeder. A length of 3.6 meters and with a test load of up to 100 grams will be the best choice. The rod has an average system, so suitable for fishing in water bodies with a standing water or low flow rate. The form is made of graphite and weighs only 270 grams.
- Model Mifine Hulk Super Feeder 3.6 meters long with a recommended test load up to 140 grams. This model is made of carbon, and its weight is slightly less than 240 grams.
Feeders Bannax Piccolo.
Bannax Piccolo is also an excellent choice for domestic fishermen, as it was designed specifically for fishing in our conditions. All blank models include an additional knee, capable of increasing their length by 50 centimeters. Excellent strength and relatively light weight are achieved due to the fact that graphite is applied during production.
Optimal models for fishing in our reservoirs are:
- Form PIC36-41 / 130. , the value of which is $ 105.
- Rod Pic36h For which you have to pay only 78 dollars.
- Fishing model PIC40-45 / 150. , the price of this model is about 106 dollars.
Feeder rods Volzhanka have a very large line of models with different characteristics. The cheapest models of this manufacturer who have relatively great quality are collected in our ranking:
- Rod Volzhanka Optima It costs about $ 50, but for this money the fisherman is provided with a parabolic rod with decent characteristics. This is the most popular model of the rod, which is produced at the Volzhanka plant.
- Form Volzhanka feeder Match This is an excellent model whose length is 3.6 meters. Replaceable elements of the design allow you to use the model in matche fishing and feeder fishing. The rod has an excellent value for money and costs only 42 dollars.
- Model Volzhanka master This is a whole range that includes rods from 3.5 meters long to 4.32, oriented to use for fishing in a variety of conditions.
Schimano Rods for Fideer
Shimano is deserved to be the most technological company in the fishing market, which, among other things, is also engaged in the production of rods for fishing on the feeder. SHIMANO feeder rods are provided in various modifications for different conditions of fishing, as well as in different price range. Our administration liked one model of the rod:
- Legendary rod Shimano Vengeance Feeder. It is considered one of the best fishing rods for beginner fishermen, which is relatively small, but does not lose the brand and is made according to the relevant quality. Removable vertex will allow fishing fishing rods both in standing water and in water bodies with the flow.
Feedher rods Daiwa.
And closure our rating of notorious fishing rodes from Daiwa. This company is engaged in the production of rods of different focus in the average price range. The best models are.
- Blanks Daiwa Aqualitefeeder. represent a whole line of models made from carbon. The minimum weight and the highest quality - that is the difference between these fishing rods.
- Feeder rods Daiwawnhf. are models of premium class. Graphite used in the production of these fishing rods is a very durable and lightweight material. For fishing on water bodies with a rapid flow of the best fishing rod just not to find.
Buy feeder rods
There are a large number of places to acquire feeders, only worth paying sufficient attention to the choice of the acquisition location. It is worth choosing only proven sales points, whether it is an online store or a simple point in the market. It is also necessary to understand that there are a large number of fake goods that cost much less than the original, but also do not provide normal characteristics.
Especially often fake not budget and inexpensive rods, but prefer the eminent brands, trying to make money on trusting fishermen. But often you can face deception and among budget rods, therefore it is worth contacting only in proven stores.
Our administration has prepared for you several reviews of the most popular models of feeders, in which their positive and negative qualities are covered. There are also reviews from real fishermen and recommendations regarding the place of purchase. We suggest you read the following articles:
- Salmo Diamond Feeder is one of the most popular lines of rods of the company, tested for years.
- Volzhanka Master is a budget version of rods with a universal set of characteristics from domestic manufacturers.
- Kaida Spirado Feeder 330 - inexpensive and at the same time high-quality rods from manufacturers from the Middle Kingdom.
- Volzhanka Optima - Domestic line of feeders, allowing you to fish experienced and beginner fishermen.
- Kaida Albatron Feeder XH - Chinese rods, tested by time, providing excellent specifications.
Catching a feeder tackle is very popular with fishermen. This way of consideration allows you to seek good catches. The feeder is considered the thinner of the bottom tower, which is effective in virtually any water conditions. Without a rod, it is almost impossible to remove large fish more than 8-10 kg. Feeder rod allows fishing at a distance of 100 meters and more. At the same time, you can catch as many fish as using multiple classic type docks. Depending on the depth of fishing, the cast range, the flow forces are selected the necessary feeder elements. The main one is a rod.
How to choose a feeder rod
Before you go for a feeder rod to the store, you should answer a few simple, but important issues. If this is the first experience, it is better to stay at an inexpensive universal "stick." As Tackage is cognition, the fisherman will appear specific requirements for the rod.
All parts of feeder gear assembly
With a long cast snap, when fishing, the feeder is required for longer length and test. It is necessary to take into account the size of the alleged trophy. For example, for catching caras in the pond, the rod is required more tender than when driving carp and sazana.
It is important to take into account the fisherman and the number of departures on the reservoir. It's one thing when a person is 2-3 times for the year, and the expensive fishing rod remains dust in the storage room. But if the fisherman has every weekend, it spends all vacations on the river or lake, then the use of a professional feeder rod is justified.
The main parameters that characterize the feeder rod are:
It is also worth considering the estimated distance or distance of the cast, the size of the fish. Primary to look at the performance characteristics of a feeder rod.
Each rod is intended for certain catering conditions. To optimally use the properties of the feeder, the weight of the rod is indicated on the weight of the thrown load or there is an inscription that speaks of limit loads.
- Inscription Light Indicates that the rod is lightweight, they can throw the snap-in with a mass of up to 30 g;
- Medium-Light speaks of the use of feeders weighing up to 60 g;
- Medium. - from 60 to 80 g;
- Medium-Heavy - from 80 to 100 g;
- Heavy. - from 100 to 120 g;
- Extra-Heavy - Over 120 g
The use of smaller feeders adversely affects the sensitivity of the feeder, and the exceeding the test limit increases the likelihood of the rod breakdown.
Feeder acquire more often under specific fishing conditions. The length of the rod depends on several factors:
- growth of fisherman;
- weight feeders;
- fishing conditions;
- Range of casts.
Currently, rods are produced with a length of 2.7 to 4.8 m in a step of 0.3 m. Some English models have their length scales.
The most common feeders are films from 3.6 to 3.9 m. Such rods are convenient to throw snapshots for the long distance.
In addition, these rods give full control over the snap. For the back of the bait for the superdult distance, a rod is required for a length of more than 4 m.
In addition, feeders with a length of 4.2-4.8 m are designed for catching for a strong course. The rod is installed on the shore vertically to reduce the segment of the fishing line in the water.
In some models of feeder rods, there is an opportunity to increase the length due to an additional knee. Thus, the fisherman will actually have two fishing rods of different lengths.
Each fisherman wants to acquire a feeder rod that will serve for many years. Reliability largely depends on the materials used.
Feeder rods are made of three main materials:
- carbon fiber;
- Composite (a mixture of "glass" and "coal").
Crawly. Despite the fact that the carbon fiber is considered modern material, he has certain disadvantages.
The most important of them is the high cost of the rod.
The second minus carbon is the tenderness and fragility of the product. Therefore, to buy a high-quality rod from a carbon fiber should be experienced and neat fishermen.
Composite. For beginners of "feeders", the "stick" from the composite material is quite used. Although such a rod is somewhat harder and tougher, but it will last long.
Fiberglass. In extreme conditions, catching (limit cast, heavy feeders, fishing of large fish) is justified by the use of rods from fiberglass.
Selecting a spinning rod - which features pay attention to, a detailed review.
How to choose the right coil for spinning or feeder rod.
Telescopic feeder rod
In different conditions, fishing is needed different models of the rod.
For catching on small rivers The best option will be a feeder from 3.3 to 3.6 m long with a test of up to 80 g of semi-prepacular or rapid system.
Fishing on a big river It will require a "stick" with a length of 3.6 to 4.2 m with a test in 80-150 g of a rapid building.
When fishing on standing lakes It is better to use the rods of the semi parabolic or parabolic system with a dough from 30 to 100 g and a length of 3.3-3-3.9, depending on the distance of fishing. If fishing is conducted from the boat, the feeder rod is best suited with a length of 2.7-3 m with a dough 20-50 gr.
Feeders of this company are familiar with most fishermen due to an affordable price with worthy quality. The best "sticks" of up to 3.6 m. Long rods are becoming severe and insensitive. Well work:
- Mikado Twin Feeder;
- Mikado Ever Green Ultra Heavy;
- Mikado Matrix 777.
Fider Rod Mikado Twin Feeder
The famous Japanese manufacturer of Fisher's Fishing Supplies produces a wide range of feeder rods, which are designed for an aneg of middle budget.
The rod form is made from high-quality carbon fiber and new geoyoral. New technologies allow you to combine elasticity and high strength in the rod, incredible rigidity and an acceptable price. The rods are well sitting in the hand of the feederist, delivering pleasant moments when digging fish.
SHIMANO BEASTMASTER FIDER ROSAR - Durable and Very Sensitive Rod
For the past two years, the Baltic Firm Salmo produces products for fishing. Fishermen appreciated budget options for feeder rods. Salmo orders components from different manufacturers. Accordingly, feeders differ not only by price, but also quality. The most expensive models will be:
- Salmo Elite;
- Salmo Diamond.
And budget feeders:
- Salmo Supreme;
- Salmo Taifun.
Feeders Banax Piccolo.
Piccolo feeder rod series is designed precisely under Russian reservoirs. They are endowed with an additional knee-insert, which increases the length of the fishing rod by 50 cm.
For example, the PIC 35-40 / 100 feeder has a length of 3.5 m, and when the knee is added, the length becomes 4 m, the model PIC40-45 / 180 can be 4 or 4.5 m.
Forms rods are made of good graphite, which gives feeders ease and power at the same time.
Banax Piccolo feeders - reliable premium rods
Daiwa Japanese feeders are able to deliver fisherman a true pleasure from fishing.
Daiwa Tournament F1 - Leader among Daiwa feeders
For catching on large rivers, the model is ideal Daiwa Aqualite Heavy Feeder which is characterized by high strength, good balancing and low weight. In enlarged diameter SiC rings allow you to use a shock leader.
And for professionals, Japanese engineers have developed an elite series of rods Daiwa Tournament F-1 Feeder . They are distinguished by unusual ease, elasticity and the highest strength.
The choice of feeder rod requires certain knowledge. If you are very novice and only comprehend all the subtleties of fishing, then our tips will be very useful for you. In this article we will focus on exactly the appropriate feeder for a beginner fisherman. Let's look through the main criteria for choosing a feeder rod depending on the terms of fishing.
What length of the feeder rod to choose
The length of the feeder rod can range from 2.7 to 4.8 meters. For the first feeder rod, it is optimally choosing a rod with a length of 3.3-3.6 m. But, choosing a feeder rod along length, you must navigate the casting range that you will need. If you are going to catch on a small lake, a pond or a ratch, you can safely choose a rod shorter - with him it will be easier for you to manage and richly overgrown with the vegetation of the shore will not be a special interference. If fishing will be held on a large river or a reservoir width more than 100-150 meters, then you will need a rod of 3.6 meters and more. Do not forget even that on a shorter and subtle rod to buy fish much more pleasant. If you plan to catch a karasik with a maximum weight of up to 0.5 kg, then it will be much more pleasant to buy it on a more delicate tackle. In addition, the rude stick when fishing a small fish is much worse depreciated, which will lead to frequent sections of the fish. If fishing is planned more than 0.5 kg fish, and this is usually carp, a crowded and Cupid, then a rival is a rival with a length of 3.6 meters, will be the most appropriate. As already mentioned above, a rod is about 3.3-3-6 meters long - the most universal. Such a feeder will allow comfortable to catch both on small and large reservoirs, it will cope with a large, and with a small fish. Therefore, if you doubt when choosing a rod length - boldly take a feeder with a length of 3.6 meters.
What test feeder to choose
The test of the blink of the rod implies the load on which it is designed, namely what weight the feeder will be used. If you use the feeder easier to the test specified on the feeder form, then you will significantly lose in the sensitivity of the feeder, and if the weight is above the upper limit of the test, then you risk breaking the rod. In the test, feeder rods are divided into: • superhigh (ultralite) - up to 40 g; • Light (light) - up to 80 g; • average (medium) - 80-100 g; • heavy (HEI) - 100-120 g; • Super heavy (extrahevi) - 120 g or more. The higher the rod test, the more severe feeder can be applied. Accordingly, the farther you can throw the bait. Also, when choosing a rod test, we should consider the water, or rather the strength of the flow in it. When catching on the current, you need to pick up a feeder with such weight that will not be demolished, so when choosing a feeder test, focus on the flow rate and the cast range. It should be borne in mind that with bad cool, it is better to use feeders as easier as possible. Often in cold water, when the fish is very careful, you have to catch a weight of 20-30 grams on the feeders. And to throw such a feeder with a dough from 60 grams from 60 grams. For light feeders, you need a more easy feeder. If you have not fully decided with what a test to choose a feeder, pay attention to the most universal version - the rod of the middle class with the upper test to 90-100 grams. Such a test will be optimal for a beginner fisherman and suitable for most causing conditions. And then, on the basis of his practice, you can understand what the next feeder test you will suit you better.
Fideer material - what better
Their price directly depends on the material of the feeder rod. Here you should make a choice based on your financial opportunities. Let's look through each material and find out their features. one. Graphite - The most expensive material for the manufacture of feeder. He has many advantages, the main thing is his weight. The feeder from high-modern graphite is really very easy and fishing with him very comfortable. Such rods withstand huge loads when digging fish, but are very sensitive to mechanical damage, such as shocks about boats, stones and other solid objects. With such rods, you need to contact very carefully and watch the knees and small pebbles in the place of the knee connecting the knees, otherwise the rod will wear it very quickly. For beginners - not the best choice. 2. Composite. Feeder rods made from the composite are an order of magnitude cheaper than graphite, but already have a greater weight. They no longer require such a gentle relationship and forgive many errors in circulation. So for a beginner, such a rod is quite suitable, and it will cost it cheaper. 3. Fiberglass. The cheapest feeders are made of fiberglass. This is the most durable material from all of the above. But such rods are pretty heavy and hard, which will cause certain inconvenience in the process of catching. For beginners who simply want to try feeder fishing - what you need.
Stroy feeder rod
By system, feeder rods are divided into: • Quick (Fast); • Medium (Moderate); • Slow (Slow). For a beginner, the optimal version will be a feeder rod of the average system, because it has averaged characteristics and ideal for an inexperienced feederist. The form of such a rod is shortened until the middle, which allows you to soften the jerks of large fish and, at the same time, do not have discomfort when casting.
What brand feeder choose
If your fishing budget is limited - do not hurry to spend all your money on the "cool" rod of the famous brand. You can try to find a relatively good chinese feeder and practice on it. The following are manufacturers that can be trusted: • Salmo; • Shimano; • Mikado; • Sabaneev; • Volzhanka.
Which coil to choose for the feeder
One of the important components of the feeder rod is the coil. The most optimal option will be the random coil of 4000 by the SHIMANO classification (3500 by DAIWA classification). Select more traction coils, that is, with a smaller gear ratio, because, when fishing is used for feeder, pretty heavy feeders are used. For this type of catching, it is more convenient for the coil with a rear friction without a baytrans. The coils described above are perfectly suitable for rods of lightweight, medium and heavy class. That is, they are suitable for all classes of feeder rod, with the exception of the most extreme - Ultra Light and Extra Heavy. But beginners, as a rule, these classes are not interesting.
We disassembled feeder rods in all characteristics and now we know what it is better to choose. Now it is necessary to collect all the new information and get a specific example of the feeder, which is perfect for a novice feederist. Although why only for beginner? Such a "stick" also uses many lovers and professionals who are not the first year of feeder fishing. So, the perfect first feeder: • 3.6 meters length. • Test - 60-100 grams, i.e. Hevi class. • Material - composite (if needed cheaper, you can fiberglass, but it is heavier). • Stroy - medium. • Coil - 4000 via Shimano. Such a feeder will be the perfect solution for you at least for a couple of seasons! Perhaps it is precisely such rods that you will use all the time. Good luck to you in choosing tackle and - no tail nor scales!
Feedher fishing is one of the fascinating techniques. Once, becoming a fiction fan, it is very difficult to seduce with other types of fishing. The feeder gives excitement, the dynamics, an accurate understanding of the processes at the bottom of the reservoir, and an extremely catch, because more than 9 years of feeder experience, the author of the article never had to leave the reservoir without a catch.
How to choose a feeder rod for beginners?
Immediately make a reservation: the choice of feeder for amateur fishing is quite simple, there are no dull spinning wisdoms, no more mathematical calculations of carpenters. In fact, everything stacked in a simple recommendation "Take a length of 360 cm and test 120, for starters enough", but encountered at one time with a similar advice, the author then experienced a lot of inconvenience. Not that this deprived this catch, but there was no convenience in casting and retracting for sure. Therefore, first you need to determine the conditions in which you plan most often catch. It can be some kind of favorite pond, ride, canal or styar, and in each case it will be different forms. First we will analyze the main characteristics, and then choose you a rod, based on your alleged terms of fishing.
The main characteristics of the feeder rod
As we said, the classification of the feeder of the type is easier than anywhere else. The test in our case implies the class, and is sometimes tied to the length, and the system is often not specified at all.
Test (class) When choosing the test, add the weight of the bait to the weight of the resulting feeds. Although all the rods for the feeder are made with a significant admission to the upper border of the thrown weight, the overloaded rod will throw not so far away, and the quiverrtip can break down when throwing. Picker - Test up to 30gr, Ultralight from the world of Fideer. Length often does not exceed 300 cm. Such rods are designed to work with light inline feeders, or without them. It is convenient to use coastal waters to 5-15 meters with them and throw along the coastal vegetation line along the distances. Often pickers serve as the second number, and stand on the spot, which is drunk with the hands. Light Feider. - Test up to 60 grams and up to 360 centimeters long. Universal rods for standing water, allowing to perform effective casts at a distance of up to 30-50 meters. Such a rod can be thrown and heavier feeders, for fishing on a weak flow. Medium feeder - Test up to 100 grams. The forms of this category are suitable for all the conditions of fishing, but the distance will be limited to 15+ meters. Experienced feeders can throw long rods close to the shore, but if you only master this kind of catching - keep in mind this restriction. Hevi Feider. - up to 120 grams. Perhaps the most common rods. The large feeder allows you to quickly flush spot on standing water, and when fishing it will not be so much to demolish the flow. Such rods are suitable for catching far from the coast, with proper boosts allow you to send a feeder at a distance of 60 meters. Extra-Hevi - 120+ grams. The most difficult and largest blanks are intended for conditions of strong flow, and heavy volumetric feeders.
The length of the rod is often tied to its class, and varies in a small framework inside it. Of course you can find pickers 4 meters long, but it will be rare, mainly they are located in the range of 1.7-3 meters. Also rare and unusual heavyweight feeders shorter than 3 meters. In most cases, there will be enough medium length 3.0-3.6 meters.
With this characteristics there may be many incomprehension. The fact is that now manufacturers immediately produce rods with a building already prepared under a certain class of rod. That is, most of the forms with a test of 80-100 grams will have the most suitable system for throwing their weight, as a rule, it is fast or superfluid. Yes, Paraboliki is better throwing light brillmen and wobblers, but throwing heavy feeder them is much worse because of the smaller speed at the beginning of the zamha. And although we can criticize experienced feeders, but we can say that recently feeders have ceased to distinguish in the rank, especially since even famous manufacturers like Daiwa and Salmo have ceased to indicate it in the characteristics of the blanks. Even on top feeder blanks stopped pointing Everything is relatively simple here. A carbonistic rod is lighter and elastic, but expensive; Fiberglass cheap and durable, but heavy; And the composite is approximately in the middle. For feeder fishing, the weight of the rod does not have such a fundamental importance as for spinning, so you can choose heavier forms with other parts of equal characteristics. According to our subjective assessment, the difference between the telescope and the plug is only in convenience and practicality. Theoretically, the plug should better throw due to the absence of the moment of inertia of the knees, but in practice, this difference is noticeable except that serious athletes. By strength, telescopic blanks have not been inferior to plug for a long time, and the large sensitivity of the plug out is not relevant for the feeder, where the bite registers a quivertip, which can be any sensitivity. The only thing that is really relevant is the weight: telescopic rods weigh 20-30% harder, but they take less space. So the choice of form factor for amateur feeder is more a matter of taste. Those very vertex alarms. Included with any feeder forms, they are from 2 to 5 pieces, different colors and with different modulus of elasticity. Stiffness increases step-in color from white, through green to red, from light feeders to severe. Sometimes more expensive forms, they subscribe to the test manner, weighing in ounces, and it causes the erroneous opinion that the peaks have a test that needs to be somehow taken into account. In fact, the vertex, up to a certain extent, does not take part in the cast, nor in the discharge, and the color or test in Oznia shows only its ability to alert the feeder of a certain weight, although it is not always true, it is worthy of these numbers as relative magnitude. Of course, if you overload the rod when casting, or you will bend in an arc when quivering - the quivertip can break, but in fact it happens very rarely. The most common breakdown - the turning of the fishing line through the tulip, and the subsequent shooting of the feeder and a half quiverrtip. Therefore, it is better not to practice spinning shuffles, but carefully bring the rod over your head, especially at first when casting. Fortunately, the quiverrtips are a consumator, and sold separately for any model of a decent rod. Visual example of the work of the quivertips of different rigidity As we mentioned, it would be wiser to choose a rod based on the place where you plan to explore the feeder tackle. It can be completely different conditions, from calm quiet ponds, to full-water rivers over the course, or immense reservoirs, choose that reservoir, where they spend the most time. On small ponds, there are quite enough light pixels up to 2.7 meters long. This is enough for the faults of all interesting places, but most often it will not be necessary, because feeding routes on low water bodies almost always take place near the shore. Flooded careers - perhaps one of the most desirable seats for feeder fishing. Big depth reveals all the advantages of bottom equipment, and the colossal sizes of the following are the usual trophy. The casting distance here plays a slightly large role, and the endurance of the form will not be superfluous, so in such conditions it is better to choose rods with a length of up to 3.6 meters and 80-100 grams test. In such places there is already a course, and interesting places on the fellows and brows are usually located at a distance of 40-60 meters from the coast. Here it will work the classic advice about the length of the 3.6+ meter and the test 100-120 grams. Best of all, such rods will manifest themselves in such conditions. The reservoirs impose great requirements for the fiderist skill: search for a place for fishing, often at a large distance from the coast, delivery of a large amount of feeding at the right point, long deploying in case of catching a large fish. For such places, the longest and most powerful forms will be suitable, allowing you to send a large feeder for 60+ meters, and withstanding a strong current.
Choosing feeder rods at the place of fishing
With this characteristics there may be many incomprehension. The fact is that now manufacturers immediately produce rods with a building already prepared under a certain class of rod. That is, most of the forms with a test of 80-100 grams will have the most suitable system for throwing their weight, as a rule, it is fast or superfluid. Yes, Paraboliki is better throwing light brillmen and wobblers, but throwing heavy feeder them is much worse because of the smaller speed at the beginning of the zamha. And although we can criticize experienced feeders, but we can say that recently feeders have ceased to distinguish in the rank, especially since even famous manufacturers like Daiwa and Salmo have ceased to indicate it in the characteristics of the blanks.
Even on top feeder blanks stopped pointing
Everything is relatively simple here. A carbonistic rod is lighter and elastic, but expensive; Fiberglass cheap and durable, but heavy; And the composite is approximately in the middle. For feeder fishing, the weight of the rod does not have such a fundamental importance as for spinning, so you can choose heavier forms with other parts of equal characteristics.
According to our subjective assessment, the difference between the telescope and the plug is only in convenience and practicality. Theoretically, the plug should better throw due to the absence of the moment of inertia of the knees, but in practice, this difference is noticeable except that serious athletes. By strength, telescopic blanks have not been inferior to plug for a long time, and the large sensitivity of the plug out is not relevant for the feeder, where the bite registers a quivertip, which can be any sensitivity. The only thing that is really relevant is the weight: telescopic rods weigh 20-30% harder, but they take less space. So the choice of form factor for amateur feeder is more a matter of taste.
Those very vertex alarms. Included with any feeder forms, they are from 2 to 5 pieces, different colors and with different modulus of elasticity. Stiffness increases step-in color from white, through green to red, from light feeders to severe. Sometimes more expensive forms, they subscribe to the test manner, weighing in ounces, and it causes the erroneous opinion that the peaks have a test that needs to be somehow taken into account. In fact, the vertex, up to a certain extent, does not take part in the cast, nor in the discharge, and the color or test in Oznia shows only its ability to alert the feeder of a certain weight, although it is not always true, it is worthy of these numbers as relative magnitude. Of course, if you overload the rod when casting, or you will bend in an arc when quivering - the quivertip can break, but in fact it happens very rarely. The most common breakdown - the turning of the fishing line through the tulip, and the subsequent shooting of the feeder and a half quiverrtip. Therefore, it is better not to practice spinning shuffles, but carefully bring the rod over your head, especially at first when casting. Fortunately, the quiverrtips are a consumator, and sold separately for any model of a decent rod.
Visual example of the work of the quivertips of different rigidity
As we mentioned, it would be wiser to choose a rod based on the place where you plan to explore the feeder tackle. It can be completely different conditions, from calm quiet ponds, to full-water rivers over the course, or immense reservoirs, choose that reservoir, where they spend the most time.
On small ponds, there are quite enough light pixels up to 2.7 meters long. This is enough for the faults of all interesting places, but most often it will not be necessary, because feeding routes on low water bodies almost always take place near the shore.
Flooded careers - perhaps one of the most desirable seats for feeder fishing.
Big depth reveals all the advantages of bottom equipment, and the colossal sizes of the following are the usual trophy. The casting distance here plays a slightly large role, and the endurance of the form will not be superfluous, so in such conditions it is better to choose rods with a length of up to 3.6 meters and 80-100 grams test.
In such places there is already a course, and interesting places on the fellows and brows are usually located at a distance of 40-60 meters from the coast. Here it will work the classic advice about the length of the 3.6+ meter and the test 100-120 grams. Best of all, such rods will manifest themselves in such conditions.
The reservoirs impose great requirements for the fiderist skill: search for a place for fishing, often at a large distance from the coast, delivery of a large amount of feeding at the right point, long deploying in case of catching a large fish. For such places, the longest and most powerful forms will be suitable, allowing you to send a large feeder for 60+ meters, and withstanding a strong current.
The reference article is based on the author's expert opinion.
Our partner - the fishing online store Kiwi-Market has provided a useful article about the right choice of Fidren rod.
Feeder fishing appeared in our country relatively recently and almost immediately became a kind of breakthrough. By borrowing all the best of the "grandfathers" bottomspoints and adding modern sports developments, the English bottom tackle became for many fishermen, the most real revelation and allowed to solve many tasks:
Performing distant and accurate casts, regardless of distance, wind strength, depth and flow;
The possibility of point feeding depending on the food preferences of the fish;
Sensitivity, comparable with the best float snaps, regardless of the catch distance.
At the same time, it is possible to achieve maximum results in the case when the tackle is assembled correctly, and feeder rods fully comply with the conditions of fishing. The slightest disregard of the main feeder rules is able to reduce all the efforts of the fisherman on no and leave it "at the broken trough."
Choose a feeder rod. What to pay attention to?
Those of the fishermen who are familiar with modern bottom methods of fishing does not interfere, know that it is not enough to buy the first feather fidel rod. Before making an order in the online store, you need to think about and answer the following questions:
In what conditions will the future catch?
What is the maximum casting distance?
What is the depth at the dot?
Is there a flow there?
What fish is alleged fishing objects?
Answers to these questions and there is the very algorithm that ensures the right choice of feeder rod in relation to specific terms of fishing. After all, rods presented on sale at the moment - a great set, and choose the appropriate option is not so simple. Pay attention when choosing is necessary for the following characteristics:
Length of the rod;
An important role when choosing a particular model of the rod plays the price. Currently, in the catalogs of famous manufacturers, you can find a variety of feeders, the cost of which sometimes differs in tens of times. It is for this reason that the frequency of trips on the reservoir should also be taken into account: if 2-3 feeder fishing are planned in the year, there is no point in buying an expensive fishing rod. And on the contrary, if the feeder "hooked", then the cheap rod is much better replaced by better and, accordingly, more expensive.
The parameter is fully responsible for the range and accuracy of the casts performed, as well as for the convenience during a digestion: the longer the rod, the easier it is to control the slaughtered fish, especially if we are talking about large copies of bream, sazana, crucian and chub. Depending on the length, all rods can be divided into several conditional categories:
Short feeders designed for fishing in the coastal zone of lakes and reservoirs. These include a model of 2.7-3.3 meters long, both feeder and pinched rods;
Rods of medium length, which can be considered universal. This includes a tackle with a length of 3.6-3.9 meters, designed for catching at a distance of up to 50 meters.
Long fishing rods, the main purpose of which is the distant feeding feeders at a distance of up to 70-80 meters and fishing in a strong wind. Depending on the needs of fishermen, the length of the best fishing rods can reach up to 4.8-5.1 meters;
According to the reviews of experienced fiderists, to consider the length of the rod separately in the root is incorrect. Therefore, another parameter directly affecting the characteristics of the tackle is its test.
This value indicates the overall weight of the feeder snap, which is capable of throwing a rod without risk of breakage. It should be remembered that this weight is absolute, taking into account the weight of the snap-in, and the weight of the bait located in the feeder, and not just the own weight of the feeders, as many fishermen mistakenly believes. Depending on the test, in the model line of many manufacturers, clear classes have been formed to which one or another rod belongs:
Pickers are lightweight and elegant rods with a test of up to 30-40 grams. Typically, produced in a length of 2.4-2.7 meters;
Light class feeders - rods that allow you to work with a snap to 50-70 grams. Have a length of 3-3.3 meters, however, there are so-called "long lights" - rods with a minimum test of 3.6-3.9 meters long;
Classic "Mediums" - tackle, considered universal. Test on a thrown snap-in in such fishing rods is about 100 grams, which allows them to use not only on standing reservoirs, but also on a river flow;
Havie class rods, having a test up to 120-140 grams, are a wonderful working tool for fishing on a river course and hunting for large and strong fish. As a rule, they have a length of 3.9-4.2 meters.
Feeders of the Exthekhevi family. The most powerful and "long-range" fishing rods, allowing to make ultra-lifting rates of snap and catch on a strong river jet. The working weight of the snap-in when fishing with such gears can reach 200 grams.
"In order to fish at distant distances of lakes and reservoirs and be able to" break through "a strong wind, a powerful rods of the HIVI class are used. To ensure the maximum sensitivity on them, elegant vertexes are installed in 0.5-1 ounces, which are able to reflect even the most careful bunch of fish. "
This classification is usually inherent in many famous European manufacturers, however, the concept of test is very often found among English feeders. It indicates the optimal discontinuous load on the fishing line or the cord used with those either by other rods.
The parameter selected with the preferences of each fisherman depending on its preferences. In 2017, it is customary to allocate three main types of building that all feeder rods possess without exception:
Quick system. Such fishing rods are distinguished by maximum sensitivity, and while working with the tackle, only the upper third of the form is loaded. Fast system is good for catching far distance, as well as for strong river flow;
Slow, or "parabolic" system. Such rods, on the contrary, bent almost from the handle itself and allow you to cope with the largest fish, using delicate snaps. It is such a building that most carp rods possesses (with a strengthening of power, of course);
The combined block of the form is characteristic of top models of famous manufacturers 2016 and this year. In this form, this form is very interesting: during the cast and extinguishing the feeder, the rod has brightly pronounced features of a quick building, and as the load increases, almost the entire form turns into operation.
What kind of stroke rods prefer - to solve you. For fishing on the river, it is better to prefer the rod rapidly. If carp and amur is planned - on the contrary, the powerful slow "stick" will be accurate to the place. Well, if you are looking for a universal tackle, we advise you to pay attention to the rod of a complex system, if, of course, the price does not scare you.
The material from which the feeder rod form is made
The very first feeders who appeared in England in the past two years have been made of glued bamboo. Similar fishing rods are popular among collectors and to this day, the simple fishermen may be interested in feeder forms made of the following materials:
Fiberglass . The most primitive and cheap material. It has a lot of weight, low sensitivity and lack of an invalidated system. The only dignity is its price: such fishing rods are inexpensive;
Crawly. The best modern material for the production of fishing rods. Low weight, excellent tactile sensitivity, the possibility of obtaining absolutely any system, magnificent thrifty characteristics - just some of the advantages of this material. There are such fishing rods are much more expensive than the "glass" analogues, but the overpayment in this case is justified;
Composite - This is a mixture of carbon fiber with fiberglass in various proportions. Medical characteristics, a democratic price tag - a typical "middle journal".
Choosing a feeder rod for a beginner, it is recommended to pay attention to the composite rods or on the cheapest feeders from the carbon fiber. The fiberglass models are suitable only to those who fish in the most difficult conditions of fishing and facing the regular probability of breaking the form while working with the tackle or retracting fish.
What feeder to choose?
Summing up the above, for fishing in specific conditions, the following models of feeders should be chosen:
For fishing in the coastal zone, the lakes and reservoirs are the best solution - a feeder rod of class Light 3-3.3 meters long and a test to 50-60 grams;
If you need a universal rod for fishing on standing water bodies or slow rivers, the optimal version is the class feeder of the medium, the length of which will be 3.6-3.9 meters, and the test will reach 100-120 grams;
Catching on a large river may require an fisherman of the use of exceptionally powerful tackle. Such will be the HEI Class feeder, 4.2-4.5 meters long and 140-160 grams test.
For a more visible display, the data is reduced to the table:
Test Test Length Applicability Picker 30-40 gr. 2.4-2.7 m. Coastal zone of standing reservoirs Light feeder 50-70 gr. 3-3.3 m. Standing reservoirs, distance up to 30 meters Medium feeder 90-100 gr. 3.6-3.9 m. Standing reservoirs, distance up to 50 meters, weak rivers Havi Feeider 120-140 gr. 3.9-4.2 m. Standing reservoirs, casting 60-70 meters, the average course of Extrahevi Rivers Feener 180-200 gr. 4.2-4.5 m. Carp fishing at 80+ distances, strong river flow.
What kind of firms prefer?
Currently, a large number of most different manufacturers are represented on the market, whose feeder rods at Kiwi-market.ru use steadily high demand. Among all this, the variety should be distinguished by the following brands, whose products are characterized by maximum quality and can satisfy the wishes of the most demanding fishermen.
The famous English manufacturer of feeder gears, which is, in its kind, the attachment of this method of catching. The rods of this manufacturer are distinguished by the consistently high quality of manufacture and applying the most modern materials and methods of their application. The absolute majority of models of this manufacturer are duplex, which has a positive effect on performance. Along with the "top" models (Matchpro, Acolyte), the model line contains and sufficiently budget fishing rodes that are enjoyable in demand:
DRENNAN RED RANGE.
DRENNAN PUDDLE CHUCKER
The Japanese manufacturer of feeder rods, operating in the fishing gear market for almost a century. This direction for the Japanese was quite new, but they managed to achieve considerable success. Fishing rods are very popular among fishermen due to the excellent quality of manufacture, a scrupulous approach to the elaboration of the smallest details, as well as a huge variety of the model line. Among budget models, the following feeders allocate:
Among expensive models, buyers celebrate the following rods:
Shimano Super Ultegra.
"People's" manufacturer whose products are in great demand, first of all, among beginners, as well as among those fishermen who know how to consider their own money. The highest quality is the manufacture, use of modern treatments and component materials, as well as the special manufacturing technology allowed the manufacturer to achieve high quality for very little money. The following models use in demand among fishermen:
SURF MASTER RIDER;
SURF MASTER PREDATOR;
SURF MASTER COMBAT;
Surf Master Nova.
Video about choosing a feeder
If you want to explore the principles for which the feeder rod is selected, and also clearly consider key aspects of specific models, we recommend to explore the photo on the Internet, as well as familiarize yourself with various video recruitment from experienced fishermen.
ЛOvvil Fish with a bottom Target One of the most vintage, traditional and common methods. It would seem that it would be simpler - a fishing line, driving, leash, a hook with a nozzle, and some kind of alarm is a bell or a plumb and a tackle. Such a donka was known in the Stone Age and familiar to any angler, who at least once in his life, can still in childhood I caught Caras, perch, bream or namimov in the nearest lake or on the river.
Time does not stand still. Developing and improving from simple to complex bottom fishing passed a long way from a primitive converge to a modern sports gear, consisting of a special rod of a long 2.7 - 4.2 meters with a sensitive tip - a pilot signaling device equipped with a non-delicant coil with a thin high-strength fishing line and snap, Based on which Georgia is a feeder and a hook leash.
The revolutionary solution to the use of the feeder - loaded in combination with a thin, but reliable tackle made it possible to radically increase the efficiency of fishing. Not by chance and the whole method, received the name Feeder, which means "feeder". Feeder-Fishing, Ledging (Ledgering) or Quivertip (Quivertip-Fishing). All these names refer to the same principle of fishing. The name "quivertip" characterizes it best because a very thin sensitive jar of a rod is most often serves as a pilot sign. Her jitter (Quivering) indicates that the bait is interested in fish.
The Motherland Feeder Methods is England, where this method is widespread, popular and read, both among athletes and among fishermen of amateurs. Thanks to its versatility today, fishing with modern English donka is one of the most popular methods in Europe. In Russia, every day the number of his admirers grows and it is quite understandable. Stunning versatility, maneuverability and convenience of this method are unlikely to be able to describe in words - it is necessary to experience it yourself! Think only! Catching occurs directly in the bait zone washed out of the feeders. The tackle makes it easy to perform long-distance and even excess of long cast, applying thin delicate snaps that do not focusing large fish. What is the tip of the signaling device?! Not any plumbings - bells, nor what a wrist! In any wind, in any wave, he restrains to bone off, after the cutting, it will not interfere, and it will be worthy of the completion of the whip of the rod of the damping fish jerk.
With modern donka, you can easily maneuver on the shore - search for fish. And finding her presence - to perform 5-6 bait casts, charging the feeder with a easily blurred bait, thus, finally attract and retain the fish in the catch zone.
The feeder is equally effective, both on the reservoirs without a flow and on the river. And it allows you to catch almost any fish, ranging from elementary roach, the gusters, bream and crucian finishing carp, Usache, Sazan and even Trout and Harius. It is purposefully for fishing large fish, currently rods are made, characterized by high power and whip strength. With such a rod allowing to apply equipment to weighing up to 250 grams easily manage even to overcome, even at a strong flow of such a strong fish as Usachi and Sazan.
Each fisherman mastering Feeder technique will certainly find a lot of various options for enhanced equipment. Isn't it in an infinite process of creativity a part of the magic attraction of fishing is concluded? So is it possible to consider Feeder by a regular donkey? Perhaps this is still something more!?
Fishermen has a lot of popularity. With her help, the fishermen constantly leave home with decent catch. The necessary elements for feeder gear are selected depending on the distance of the cast, the depth of fishing, the presence of the flow and its strength. Feedher rods are one of the main elements that provide equipment to the equipment.
Fider Rod Choice Guide
Before you go to a fishing store to choose feeder rods, answer yourself a list of simple, but at the same time very important questions:
- Do you have experience fishing for feeder? If not, it does not make sense to paint tears to select the characteristics of the feeder snap. You will not need to notice their differences yet. And gain experience easier with a universal stick. Otherwise, you will often disappear by breaking gear. You yourself will understand when it is time to make a rideway specific requirements.
- How far are you going to throw the tackle? Is there a flow of water where you are going to fish? What is the size of the expected production? Having answered these questions, the choice of feeder rod will be simplified, since the length and test will already be determined.
- How many times do you go fishing? Do not wastely spend money on a stick if you choose to the reservoir just a few times a year. If you have the opportunity to fish often, you should see and choose professional feeder rods.
Fider fishing rod is characterized by three main parameters. This is a test, its length and material from which it is made. Depending on the conditions of future fishing, one or another rod with a variety of parameters is chosen. The larger the stick is suitable for specific conditions, the more successful fishing.
Test rod for feeder
Test Rod - This feature that says the fisherman about how the range of weights can be caught fish on this tackle. Each stick is designed for fishing under concrete conditions. To use the feeder properties to the maximum, you need to use a suitable rod for a certain weight of the bait. On the Fishing Blanca, the range of admissible masses of bait is always indicated:
- Light, or "Light" (L), are designed to catch fish with weight of bait up to 30 grams;
- Medium-deep, or "medium-light" (ML) are designed for fishing with a feeder with a mass of bait up to 60 grams;
- Medium rods, or "medium" (M), are designed to use feeders weighing from 60 grams to 80;
- Medium-heavy (medium severity), or "medium-heavy" (MH), are needed when the mass of bait oscillates in the range from 80 to 100 grams;
- Heavy, or "heavy" (h) are intended for fishing fish to a feeder weighing from 100 to 120 grams;
- Super heavy, or "Extra-Heavy" (EH), are needed for fishing with feeders weighing from 120 grams.
It is necessary to strictly observe the test of the test. Rod weight of the feeder. If the load is less than indicated in the range, the sensitivity of the fishing rod decreases dramatically. At the same time, you will not be able to observe careful bite. If you will use the bait harder than provided by the test, that is, the likelihood that the rod will simply break, because when casting it is experiencing a strong load.
Length feeder fishing rod
Today, feeder rods can have a length of 270 to 480 centimeters. The step at the same time is equal to 30 centimeters. But this does not concern some English models. The most popular are sticks whose length is 360 or 390 centimeters. With their help it is easy to throw the feeder for a long distance. Rods with so long allow full control over the tackle.
If you are going to catch the fish with a strong current, then sticks are required for more than 4 meters long. Such long fishing rods are needed if the rival is produced at ultra-dollar distances. Such a length of the stick with a strong flow is needed to reduce the segment of the fishing line, which is in water. For this, the rod is put in a vertical position.
Some manufacturers offer individual tips to feeder rods. With their help, you can change the length of the rod. It is very convenient, as it disappears the need to buy 2 rods. Instead, you can buy one, but with an extra knee.
Fideer sticks Modern producers are made of carbon fiber, fiberglass or composite, which contains in itself, both "coal" and "glass". Cage is considered the most popular and modern material, but it also has its own cons. To them, first of all, there is a high cost. The lack of disadvantage is also fragility, some tenderness of the material. Therefore, this tackle will not be for beginners, but for mothers of professional fiderists.
For beginners, it is best to choose a stick from the composite. It is rigid enough and durable: it's just necessary to fill your hand, trained. If you need the most distant cast, you catch the fish with the most heavy feeders or hunt a trophy fish, then you need the most durable rod. So there will be a rod of fiberglass.
Fiberglass for the presented gear will give them a big weight. Therefore, it is chosen for the implementation of long-range casts and fishing of large fish. Such equipment should be kept on the stand, otherwise your hands will get tired of keeping
Stroy feeder rod
We call the parameter denoting the mechanical stiffness of the whip. The system is a characteristic that determines the shape of the bend of the stick during when you cast.
Structure of the feeder rod when choosing for beginner fishermen should be one of the main parameters. It makes it clear what rigidity (elasticity) has a package of tackle.
There are basic three types of building:
- Fast, or "fast";
- Slow, or "slow";
- Medium, or "medium", sometimes "Moderate".
- You can very rarely meet fishing rods with a building "Medium-Fast", which means - average, or borderline.
The photo shows how the rod is bent. Bend is immediately visible, what system in the stick. Moreover, the faster the course of the river, the flexible should be a stick. And for standing reservoirs, the middle or slow system is perfect.
Rods of fast building have rigid structures in the middle and lower parts of the whip. When you throw a fishing rod, only the top of the stick is bent. It is usually raised about a third of the rod length. It is called the system to quickly because it is quickly extended after the cast.
Slow stroke rods across the entire length have the same rigidity. From this stick bends when casting by more than 66% of the total length. She is warmed very slowly, therefore he received such a name. But the average system of fishing rod allows it to bend when casting for a length that does not exceed 2/3 of the rod length. It is slower slower than the fishing rods with a rapid system, but faster than with slow.
Structure of the feeder rod when choosing for beginner fishermen should be one of the main parameters. It makes it clear what rigidity (elasticity) has a package of tackle.
Fast unit belongs to a rigid rod. With the load, only the top and the first knee will be bend. Such a system is considered the best when choosing a feeder rod on carp. When careing fish for squiggings, this quality will allow you to control it in the process of leasing.
The slow system allows a rod to bend on all the knees, which will avoid the break of the leash.
To decide how to choose a feeder rod for beginners, a product should be purchased with a complex system. Such a tackle bends only on top at low loads, and with a strong resistance of large fish all its knees will be moved. This will determine which feeder rod for carp fishing will be more comfortable for fisherman.
KVIVERTIP - Feeder Top
A distinctive feature of the feeder from ordinary spinning is the presence of replaceable vertices. They will sign a fisherman about bite. Usually, 3-4 vertices are supplied with the feeder.
This element has its own test. With the help of the color indicate the rigidity of the quiverrtip. The red peak is the toughest, orange or rigid possesses medium flexibility, and the green is the most mild.
The type of vertices are selected in accordance with the conditions of the reservoir. If the current is strong, you should choose rigid quiverrtips. Soft elements of the rod will be able to more accurately transfer the signal about bite in quiet water without excitement and flow.
In the event of a quivertip breakdown in case of random strike or strong inflection, you can pick up an identical product in the store. You should consider the diameter of the base when choosing. It must correspond to the value provided by the manufacturer.
With all the careful attitude to the tackle, it is possible that the feeder vertex will break (sniffing for a tulip, a random blow about the branch at the time of cast, etc.). And you need to be prepared! Therefore, buying feeder, pay attention to the diameter of the vertices at the connection site. The most common diameter is 2.2 mm and 3.5 mm, other diameters are not easy to find in case of breakage. Ask, from what material they are made (fiberglass, carbon fiber, carbon fiber) as with the same test they will have different sensitivity that radically changes the indication of the bite.
It is better to buy those tips (they are complete with a rod), which are marked with a numerical value, and not with color marking due to the presence of a significant error of the stated test. Numeric indicators are applied in English ounces (approximately 1 ounce is 28.35 gr.), As evidenced by the abbreviation "OZ" or in grams - "G", for countries where the unit is served by the latter. Of course, the vertices without numeric labeling can also be caught, but the absence of the necessary skills to stretch the quivertip to the working condition will definitely affect the results of fishing newcomers.
Do not be lazy when buying checking the compliance of the test of the form and the correspondence of the test of the vertices. Very often, "randomly", they do not coincide on budget and cheap feeder rods!
Blow rings are subjected to a powerful load during fishing. Their quality and strength play an important role for the feeder. High-quality rings often produce independent manufacturers. Therefore, Salmo feeder can be Fugi's rings. Quality products also produce Balzer, Dam. By asking how to choose a feeder rod, you should pay attention to the mounting of the flowing rings. For good quality products, these elements are attached to three legs. Inserts inside the rings are capable of extending their service life.
What models rods are better under diverse conditions
Pick up the gear for fishing on the feeder to make the most of their properties. So, for fishing on small robes, the best rods will be a length of 330 or 360 centimeters. The optimal rod test is medium, and the system is fast or parabolic. On large rivers with a strong flow, it is best to use the rods of 360, 390 or 420 centimeters long, the test must be heavy or superheavy, the system is fast.
The best rods for standing reservoirs must possess parabolic or slow build. The length of them should not be big if you are not going to make long-range casts. It will completely come down a stick from 330 to 390 centimeters. And for fishing from the boat, you do not need to look for a fishing rod longer than 300 centimeters. The test is suitable easy or middle.
Coil for Fidera
One of the most important elements of the fider's rod is the coil. It should be powerful and reliable in order to withstand the load when leasing fish out of the water.
The spool of this element should be quite large to accommodate a sufficient amount of fishing line.
In order for novice fisherman to understand how to choose a feeder rod and coil, you should pay attention to the number of bearings in the model. For such a fishing rods, coils with a minimum of 6 bearings are suitable. The highest quality instances can have up to 15 bearings.
The transfer number of the coil is an important indicator. He gives to understand how many revolutions makes a spool with one knob cycle. The gear ratio indicates the winding speed. In a universal coil, this indicator is in the range from 4.6 to 5.5. It is also allowed to use high-speed coils with the number of revolutions above 6.
Another indicator, decisive, how to choose a feeder rod and a coil for beginners, is the presence of an adjustable friction brake. It can be front or rear. The coils with the front brake is usually easier and more compact.
A brief overview of the most popular rods for the feeder
In the fishing gear market, several manufacturers have proven perfectly. They make gear from high-quality materials using modern technologies, so in reliability you can not be doubted. Be sure to look at rods:
Mikado. This firm has become famous not only by magnificent feeder sticks, but also available prices for a wide range of fishermen. The best fishing rods are recognized by sticks with a length of 360 centimeters. Mikado long gentle gear is better not to choose, as they are too heavy, which is significantly lost sensitivity;
Shimano. This is a Japanese manufacturer, which offers a wide range of feeder rods. To buy them, you must have a middle budget. Basically, fishing rods are made of carbon fiber. Shimano is also experimenting with a completely new material, which is called geo-solok. Geoyoral allows you to achieve high-strength and elasticity of the rod at the same time along with good rigidity. Such sticks are comfortable to keep in hand;
Baltic firm called Salmo. produces sticks for fishermen with a weak budget. However, the company has no own manufacturing base, it orders components from other fishing companies. Therefore, the quality of the gear is at the proper level;
Feeders Banaks Picolo Developed specifically for fishing in Russian conditions. Each model has an additional tip that increases the length of the stick for 50 centimeters. Fishing rods made of high-quality carbon fiber - graphite, which is very easy and power;
Present pleasure from fishing fishing can get when catching fish with Japanese feeders Dave . In a wide range you can find both professional light rods and heavy. Tackle have unsurpassed strength.
For feeder fishing, they use both mononium and wicker products. For novice fishermen carp experts advise to acquire a fishing line with a diameter of at least 0.16 mm. Also should pay attention to the strength of the load that the braid or fishing line should withstand. To be reinforced, you can also choose a diameter of a mononimity of 0.18 mm or 0.16 mm for a wicker fishing line. You need to take into account the quality of the flow rings when selecting the fishing line. If a cheap feeder is purchased, its rings rarely have additional protection in the form of dense inserts inside. For such products it is suitable to monnion, designed for a slight fish. For the wicker, the rings must have protective inserts so that in the fishing process does not occur.
After reading all the features that should be considered in solving the issue, how to choose a feeder rod, a beginner fisherman will be able to choose the optimal option. Relying on the recommendation of experienced experts, you can not doubt the successful choice of all necessary gear. Fishing with the help of proper equipment will bring a sea of good mood and unforgettable impressions.