What is an engineering board, characteristics, advantages and disadvantages

In the flooring market, a separate category contains multilayer finishing materials. This class includes the so-called technomissive or engineering board.

Characteristics

Combined wood coatings are considered more stable than the usual one-piece array. In Europe, they are customary to be called modular, that is, we combine massive and mixed with wood fillers. One of the most interesting "representatives" of this category is an engineering board.

The technomassium consists of two layers:

Carrier base

It is a birch moisture-resistant phanener of varieties I or extra. The thickness of the formation varies from 6 to 16 mm. Callery connections of three types are cut around the perimeter: Puzzle, PAZ-grooves (key) and snap-down Click format.

Decorative veneer

Sing of valuable wood breeds 2.5-7 mm. Since the surface should be resistant to abrasion, shocks and mechanical damage, such solid varieties are used as oak, ash, tick and others. The thicker layer, the greater the number of restorations will withstand the coating. For example, an engineering board for floors with a useful look at 5 mm admits up to 4 grinding and update procedures.

From above, the coating is processed by protective varnish or oil-wax mixtures. To underline the texture of the outdoor material in the factory conditions, various decorative techniques are used: smoking, brashing, filling, etc.

Since the engineering board is made both as an independent product, and under the order, its dimensions vary in large limits:

  • In length - from 50 to 600 cm,
  • In width - from 12 to 45 cm,
  • In thickness - from 12 to 20 mm.

For comparison, the thickness of the parquet board does not exceed 16 mm, the length is 3 m. That is, the technomascus is really so stable and durable that it can be released in any sizes without the threat of deformation damage. One fact makes many make a choice in favor of engineering.

Curvoline engineering board in the interior.

We call another interesting characteristic of the modular coating. As you know, it is now fashionable to emphasize the naturalness of the finishing material, its texture and color. For this, the parquet is subjected to brash, hardening, toning, burning, even the imitation of worm and strong scuffs are cut out. But engineering board manufacturers went further and offer not standard rectangular planks, but curvilinear, as in the photo below.

When assembling, a canvas with uneven longitudinal grooves is formed, which is characteristic of the board, made completely manually.

Advantages and Disadvantages of Technomassive

Engineering board is an excellent finishing material. And the proof of this statement is a whole set of advantages over the analogues:

  1. High level of geometric coating stability, which minimizes the risk of strain deformation;
  2. A wide choice of formats, thanks to which it is possible to choose coatings for rooms with the bottoms of the base;
  3. A variety of designs and decors. The assortment is present both by the factory-processed method and clean lamellas, the surface of which the buyer can be covered with any wood agent;
  4. The possibility of multiple renovation (grinding) and restoration (replacement of damaged sites);
  5. Durability - the average life of high-quality coatings is 20 years, maximum - up to 40 years;
  6. It is possible to manufacture products to order for selected sizes and shades;
  7. The diversity of installation methods: adhesive, combined, fastener, lock, in the key, etc. In addition, deck and figured laying is allowed, for example, the "Christmas tree", "squares", and the like.
  8. Combination with floor heating systems: water, thermomatics.

Minuses:

  • High cost compared to other modular coatings;
  • Complex installation and dismantling process;

These two positions can push the potential buyer, but it is worth remembering that the high-quality finishing material serves a long time and fully justifies the funds invested in it.

Methods of installation

Above, we noted that the indisputable advantage of technomassiva is a variety of coating assembly options. These include such as:

Glue

The polymer compositions of one or two-component are used. Any durable, solid and smooth material is suitable as the basis: screed, plywood, chipboard, osp. The exclusion is bulk gypsum floors and a cork substrate (due to its softness). Before work, it is necessary not only to prepare the basis, but also to pre-calculate and draw a layout plan.

Combined: glue and fasteners

Here is a choice:

  • Glue and fasteners (studs, screws, nails). The adhesion mixture is applied to the base, and hardware robbed into the grooves of each strap at an acute angle. Excellent combination for durable floor;
  • Adhesive compound based on the base and key insert, which prevents the displacement of the flooring and providing a dense connection. This method is recognized most practical and very laborious, but the result obtained is effort.

"Floating"

The engineering array with lock connections is not often produced, it is mainly a registered position. If buyers want quickly and minimally to get high-quality, reliable coverage, then plants can make a party. Installation is carried out by standard deck method using the substrate. The size of the boards should be no more than 2.2 meters to facilitate stacked work and ensure a dense circular cutting of locks. The prerequisite is the ideal basis for the basis and presence of compensatory seams around the perimeter.

For a detailed acquaintance with the technology of installation, we recommend reading the article: Engineering Plaque Stacking Technology.

Do not forget that the surface of the coating is a solid veneer of the array, so each plank will be slightly different from the adjacent pattern, texture or tint. But the collected floor due to this looks natural, beautiful and absolutely unique.

Tip! If you need a floor repair masters, there is a very convenient service for the selection of specialists from profi.ru. Just fill in the details of the order, the masters themselves will respond and you can choose who to cooperate with. Each specialist in the system has a rating, reviews and examples of work, which will help with the choice. Looks like a mini tender. The placement of the application is free and does not oblige anything. It works in almost all cities of Russia. Without your desire, no one will see your phone number and will not be able to call you until you yourself open your number to a specific specialist.

If you are a wizard, then go to this link, register in the system and you can receive orders.

The most readable

Choosing an engineering board as an outdoor coating in an apartment or house, it is important to learn about its advantages and minuses. About this speech in the article

Choosing an engineering board as an outdoor coating in an apartment or house, it is important to learn about its advantages and minuses. It is impossible to consider the material only from aesthetic point of view, although here it stands in the same row with parquet. 1. Inshenernaya Doska.The article will describe the nuances of the advantages and disadvantages of the coating.

Content:

What is an engineering board

The coating is a two-layer or three-layer board. 2. Dvuhsloinaya doska.The last option is similar to the parquet, but in contrast to natural wood, this floor material is not entirely natural, as it contains the woodworking product - Phaneur. Its layers are glued together with silicone additives. Decorative top facial layer - sawn veneer from valuable wood. Read more about sizes - here. The strength qualities of the coating depend on the parameters.

Views

In addition to classification on the number of layers, the engineering board is divided into the following types:

1. The method of cutting the upper layer. 3. Metodi Raspila.The parameter is identical to the classification of parquet. Grade - Select, Natur, Rustyl - emphasize the natural drawing of the tree. In the first case, defects are unacceptable - knots, contrasting transitions of tones. The floors become a single area. In the second - they are allowed in small quantities. In the third - the coating is motley due to splashes and color transitions. Appropriate and price. Method of processing engineering board. In addition to the decorative layer of varnish or oil, the board is subjected to mechanical processing - the brushing, when the soft fibers of the wood are removed and the structure of the barrel thanks to the solid lodgings is pronounces clearly. 4. Clean-umbra-brashOften, the design use the aging method - the floors resemble the species, but without losing the strength characteristics. 5. INSHENERNAYA DOSKA METOD STARENIYAPopularly a filling, which gives the board even greater stability and not exposure to the environment. Number of strips. Engineering board contains from one to three stripes of the facial layer. 6. 2Polosnaya doska.The last copy is identical to a piece parquet due to dice sizes.

Tip - choosing an engineering board for laying in one room, it is important to determine immediately with the appearance and number of material. Then pick up a common tone and the number of strips of the upper layer - difficult. In case of inconsistencies and the inability to purchase a similar board, the coating of the circular and tinted.

Advantages and disadvantages of engineering board for specific conditions

The wooden floor covering has pros and cons inherent in natural material. It is important to consider the engineering board, from the point of view of durability, for each room, where it is supposed to be treated. Consider detail:

Living room

For her, a parquet board is an ideal solution. 7. DOSKA V GOSTINOILoads The room is experiencing point, furniture - sofas, armchairs. The passage activity is high and dignity of engineering board - strength - with honor withstanding the test. With the material, create in the living room Eco or Country style in the living room is easy - for this, the brushed board covered with butter or varnish is selected. Terms of choice of engineering board in the living room:

1. Felt or rubber lining under the feet of furniture. Timely care.

Bedroom

Stand on a warm floor after sleep - a great feeling. 8. DOSKA V SPALNENatural material does not require additional heating systems due to its structure, but receive an electrical or film network. Water warm floors for the species of wooden coatings are prohibited due to random possible leakage. The durability of the engineering board in the bedroom increases due to the low passage of activity and the protection of the pile coating - the carpet, the palace. Care conditions are similar.

Children's

The great dignity of the engineering board in the nursery is its naturalness of the layers, and, therefore, environmental friendliness. 9. Doska v DetskoiFrom the coating it is impossible to obtain allergic reactions, it is not static, the content in silicone additives does not affect the atmosphere of the children's room. However, the passability of the children's room is increased, therefore, the impressive parameters of the engineering board are required. It has a wide size range - one more advantage.

Kitchen, hallway, bathtubs and bathrooms

Unfortunately, the main minus of any natural wooden board, despite the number of layers and stabilizing layer - the fear of moisture. 10. VZDUTIE DOSKI V VANNEThe engineering board is manifested in less than that of the parquet, but, nevertheless, more than that of the laminate. Therefore, as an outdoor coating in bathrooms, bathrooms or kitchens, the engineering board is not recommended. The rooms are distinguished by an aggressive and wet environment. In addition, the board has the ability to absorb odors.

For hallways, an engineering board is unacceptable due to all aggressive factors - moisture, temperature drops, dirt. This plot in an apartment or house has the highest active passability. Requirements for cleaning, elevated - daily dry cleaning with stain removal. 11. INSHENERNAYA-DOSKA-V PRIHOSHEIThe content in the original form of the engineering board is troublesome and almost impossible.

Conclusion

Summarize. The advantages of the engineering board include: the environmental friendliness of the material, strength, beauty, the possibility of self-laying and the stability of the floor under the appropriate conditions. Cons: Fear of moisture, care requirements, regular refreshment of the facial layer and a short time in case of incorrect selection of the parameters. Smooth negative impressions and enjoy the beauty of the coating, perhaps only subject to the implementation of the recommendations for choosing an engineering board into each room.

If you have found a mistake, please select the text fragment and click Ctrl + Enter. .

In the flooring market, a separate category contains multilayer finishing materials. This class includes the so-called technomissive or engineering board. What it is and what is his advantages - read in our article.

Engineering board characteristics

Combined wood coatings are considered more stable than the usual one-piece array. In Europe, they are customary to be called modular, that is, we combine massive and mixed with wood fillers. One of the most interesting "representatives" of this category is an engineering board. What is special in it and what attracts? Let's figure it out.

The technomassium consists of two layers:

Carrier base

It is a birch moisture-resistant phanener of varieties I or extra. The thickness of the formation varies from 6 to 16 mm. Callery connections of three types are cut around the perimeter: Puzzle, PAZ-grooves (key) and snap-down Click format.

Decorative veneer

Sing of valuable wood breeds 2.5-7 mm. Since the surface should be resistant to abrasion, shocks and mechanical damage, such solid varieties are used as oak, ash, tick and others. The thicker layer, the greater the number of restorations will withstand the coating. For example, an engineering board for floors with a useful look at 5 mm admits up to 4 grinding and update procedures.

What is an engineering board and what is its advantages over an array?

Building engineering board.

From above, the coating is processed by protective varnish or oil-wax mixtures. To underline the texture of the outdoor material in the factory conditions, various decorative techniques are used: smoking, brashing, filling, etc.

Since the engineering board is made both as an independent product, and under the order, its dimensions vary in large limits:

  • In length - from 50 to 600 cm,
  • In width - from 12 to 45 cm,
  • In thickness - from 12 to 20 mm.

For comparison, the thickness of the parquet board does not exceed 16 mm, the length is 3 m. That is, the technomascus is really so stable and durable that it can be released in any sizes without the threat of deformation damage. One fact makes many make a choice in favor of engineering.

What is an engineering board and what is its advantages over an array?

Curvoline engineering board in the interior.

We call another interesting characteristic of the modular coating. As you know, it is now fashionable to emphasize the naturalness of the finishing material, its texture and color. For this, the parquet is subjected to brash, hardening, toning, burning, even the imitation of worm and strong scuffs are cut out. But engineering board manufacturers went further and offer not standard rectangular planks, but curvilinear, as in the photo below.

When assembling, a canvas with uneven longitudinal grooves is formed, which is characteristic of the board, made completely manually.

Advantages and Disadvantages of Technomassive

Engineering board is an excellent finishing material. And the proof of this statement is a whole set of advantages over the analogues:

  • High level of geometric coating stability, which minimizes the risk of strain deformation;
  • A wide choice of formats, thanks to which it is possible to choose coatings for rooms with the bottoms of the base;
  • A variety of designs and decors. The assortment is present both by the factory-processed method and clean lamellas, the surface of which the buyer can be covered with any wood agent;
The possibility of multiple renovation (grinding) and restoration (replacement of damaged areas); engineering board cycloying.
The possibility of multiple renovation (grinding) and restoration (replacement of damaged areas); engineering board cycloying.
  • Durability - the average life of high-quality coatings is 20 years, maximum - up to 40 years;
  • It is possible to manufacture products to order for selected sizes and shades;
  • The diversity of installation methods: adhesive, combined, fastener, lock, in the key, etc. In addition, deck and figured laying is allowed, for example, the "Christmas tree", "squares", and the like.
  • Combination with floor heating systems: water, thermomatics.

Minuses of engineering board:

  • High cost compared to other modular coatings;
  • Complex installation and dismantling process;

These two positions can push the potential buyer, but it is worth remembering that the high-quality finishing material serves a long time and fully justifies the funds invested in it.

Engineering Board Mounting Methods

Above, we noted that the indisputable advantage of technomassiva is a variety of coating assembly options. These include such as:

Glue

The polymer compositions of one or two-component are used. Any durable, solid and smooth material is suitable as the basis: screed, plywood, chipboard, osp. The exclusion is bulk gypsum floors and a cork substrate (due to its softness). Before work, it is necessary not only to prepare the basis, but also to pre-calculate and draw a layout plan.

Combined: glue and fasteners

Here is a choice:

  • Glue and fasteners (studs, screws, nails). The adhesion mixture is applied to the base, and hardware robbed into the grooves of each strap at an acute angle. Excellent combination for durable floor;
Adhesive compound based on the base and key insert, which prevents the displacement of the flooring and providing a dense connection. This method is recognized most practical and very laborious, but the result obtained is effort.
Adhesive compound based on the base and key insert, which prevents the displacement of the flooring and providing a dense connection. This method is recognized most practical and very laborious, but the result obtained is effort.

"Floating"

The engineering array with lock connections is not often produced, it is mainly a registered position. If buyers want quickly and minimally to get high-quality, reliable coverage, then plants can make a party. Installation is carried out by standard deck method using the substrate. The size of the boards should be no more than 2.2 meters to facilitate stacked work and ensure a dense circular cutting of locks. The prerequisite is the ideal basis for the basis and presence of compensatory seams around the perimeter.

So, we figured out what kind of engineering board. Do not forget that the surface of the coating is a solid veneer of the array, so each plank will be slightly different from the adjacent pattern, texture or tint. But the collected floor due to this looks natural, beautiful and absolutely unique.

Request to those who do not care, please put Like (thumb up) And subscribe to my channel. Constantly on the channel there are articles about the manufacturer, restoration, coatings of wooden products. I invite you to heartily - Sign up! I'm happy! :)

Engineering board - a new variety of flooring, produced from natural wood. The coating is obtained durable, environmentally friendly and reliable.

In the laid form of the floor from the "engineer", so this material is briefly called the wizard, it looks like the one that is made from a massive board. Engineering board has retained all the advantages of massive: it is natural, durable, adds the status to any interior. At the same time, the flooring of the engineering board will cost you cheaper than the coating of the wood array.

Three reasons why engineering board is more economical:

  • Material is cheaper in production due to plywood layer;
  • below the costs of means for laying;
  • Less costs for mounting work.

Engineering board design

Engineering board is arranged: the base of the birch plywood plus layer of wood of valuable breeds (oak, acacia, elm, etc.). Birch plywood tenter and tight conifer, from which, for example, make the inner layer of the three-layer parquet. Due to this, the flooring is obtained stable and stable, not afraid of the drops of moisture and temperature.

On the species, the engineering board is similar not only to the massive board, but also on the parquet, especially if it is posted a classic "English Christmas tree". Such a coating looks very stylish, fit into classic, and in modern interiors.

Engineering board, Laying "English Christmas Tree":

Advantages and disadvantages

Advantages of engineering board:

  • Unique natural drawing of each dice;
  • The floor is obtained warm to the touch: the tree is an excellent heat insulator;
  • High sound absorption - the tree itself is a good soundproofer;
  • After laying, you do not need to lacquer the surface - a varnish coating is applied to the plant on the boards, resistant to ultraviolet.
  • durability - service life of up to 50 years;
  • Ecology.

The durability of the engineering board is worth noting separately. The thickness of the upper layer, which is made of wood of valuable breeds, is 2.5 mm. With the right operation, the first time to update the varnish will be necessary in 10-15 years. For one grinding, 0.2-0.4 mm of the upper layer is removed. That is, the floor can be grinding up to five times.

The disadvantages of the engineering board include a higher cost compared to other floor coatings (with the exception of a massive board and some types of parquet). The price is compensated by the durability of the material.

Engineering board - an excellent choice for those who appreciate environmental friendliness, naturalness and durability.

Using

Engineering board thickness - 12 mm, wear resistance class - 23. Such a coating can be used for rooms with low, medium and high load. The board is ideal for living room, bedroom, children's and office.

Remember two important points. First: Engineering board is not suitable for rooms with high humidity. The second: the mounted coating cannot be dismantled, transported and minimized.

Connection options

Most engineering board samples are equipped with a spike-groove compound. Spike and grooves are notches and recesses that are located around the perimeter of the boards.

How the spike-groove compound is arranged:

The spike-groove board cannot be laid with a "floating" method, with a lock connection - it is possible.

For example, this model, "Acacia Burmanskaya" with a castle compound. This engineering board can be laid "floating" in the way.

Engineering board can be laid on concrete or plywood base.

Methods of laying

Laying "floating" way

This is the best and simple version of styling engineering board. Recall, so you can mount only samples with a lock connection.

The main disadvantage of the method is to reduce the coating service. The main load during operation falls on the castle, over time it weakens, gaps are formed between the dies. Consider: with a "floating" method, the coating cannot be polished.

Important information: To increase the service life of the floor covering, even the chalkboard with the lock connection must be placed on glue.

Concrete base

On the concrete base, you can lay the board with a spike-groove compound, and a chalkboard with a lock connection. This is a quick and inexpensive way.

When laying on concrete, it is important to comply with three rules:

  • The base should be dry, smooth and durable;
  • You can use only elastic polyurethane glue, it will give the board the possibility of a little "walk";
  • The staple board must be pressed with heavy objects, for example, packages with ceramic tiles or bottles with water.

Stages of work:

  1. Click up the concrete screed;
  2. Secure the boards with glue;
  3. Install uniform goods along the entire length of the boards - so the dies are stripped with each other and firmly fall on the floor.

Fanroom base

This is the most reliable way of installation, it ensures the stability of the floor covering.

Stages of work:

  1. Take moisture-proof plywood, cut it with squares with a side of 30-40 cm;
  2. Put the Phaneur to the primed base - the squares should go in a checker order ("with a tightening" on the principle of the construction of a brickwork), with a gap between tiles in 3-5 mm;
  3. Secure the Phaneur to the glue or shoot with dowels;
  4. When the glue dries, proceed to laying the engineering board.

Details:

  • Use two-component polyurethane glue, it must be applied to the base using a toothed spatula;
  • The engineering board can not be stacked close to the walls, the gaps from 10 to 15 cm wide should remain around the perimeter of the room;
  • The boards need to be attached to a plywood with self-tapping screws, they screw in spikes of boards at an angle of 35 °.

Combined method of laying

The method recently appeared, a special screen substrate and glue is needed for mounting. The substrate is placed on a concrete base.

List of necessary goods from the Assortment of Lerua Merlin:

  • Stencil - a substrate with groceries, which clearly define the boundaries for which glue should be applied; The size of mats - 8.5x1.1 m, thickness - 2 mm;
  • elastic single-component glue on a polyurethane basis;
  • Adhesive gun (syringe-dispenser).

The substrate with slots should be spread along the location of the boards, so that the slots lay perpendicular to the dies. Then the slots should be filled with glue.

The advantages of the combined method:

  1. Reliability. Due to the elasticity of glue, the coating is obtained durable and stable to loads.
  2. Economicity - such styling will cost cheaper than the installation of boards on Faneur and glue.
  3. Soundproofing: The laid board absorbs the reflected sound with a volume of up to 16 dB.
  4. The method saves from one centimeter of the room height, since the plywood layer is not required.

Helpful advice: If glue hit the front side of the engineering board, remove it immediately with acetone so that there are no traces left. Remember: After styling the engineering board, it is impossible to walk within 24-48 hours, the exact time depends on the glue used.

Tips for care

  1. After laying the gaps around the perimeter of the room, it is necessary to close the plinths. Plinths we advise you to pick up the color of parquet or interior doors.
  2. Be sure to make felt or rubberized substrates on the legs of furniture - so you will save the floor from scratches and dents. For rolling chairs and chairs, select special rubberized rollers for the parquet or under such a protective rug under such furniture.
  3. Cleaning tools must be without metal edges. Dust, sand and other small particles should be removed using the usual (not washing) vacuum cleaner or soft brush.
  4. The floor from the engineering board should be washed well pressed with a damp cloth or mop. It is important not to allow puddles.
  5. If complex spots appeared on the surface, use a special cleaner or a regular alcohol solution.
  6. Do not use abrasive materials, acids, solvents, chemically active substances and powder detergents to clean the floor. Before applying a new detergent, make sure it is suitable for wooden floors.
  7. So that the floor covering as long as possible, we advise you to maintain air humidity 40-60%. The perfect temperature in the rooms is 18-22 ° C.

Choose an engineering board in Lerua Merlin hypermarkets network and on our website. Do not forget about consumables and tools for laying, as well as about the flooring tools.

What is an engineering board

Engineering board is a kind of improved "analogue" of natural wood. There are many things between these materials, but there are also fundamental differences. So, the engineering board is a multi-layered material with an upper decorative layer of natural wood - oak, ash or nut, teak.

As a lower layer (stabilizing base), high-quality plywood is used, in which internal and external propuls are made. The plywood layer is several sheets glued with each other (the direction of fibers with gluing alternates).

inzhenernaya_doska.jpg.

It turns out that approximately 1/4 part is a woody array, and 3/4 - plywood. This design provides good resistance to mechanical effects, temperature expansions and high humidity (and these characteristics exceed similar to the parquet). In addition, it allows you to significantly reduce the cost subject to the preservation of high performance.

Maintainability, the ability to restore the upper coating (restoration of the oil or lacquer protective layer, as well as the total permissive) are fully stored, as in a massive board. The only thing that engineering board differs from the massif is the existing limitations in size (up to 30 cm - width and up to 3 m - length).

Structure of material. Engineering board characteristics

injenernaya_doska.jpg.

Combined or modular wooden coatings are more resistant to external influences, the week is a whole array, sensitive to temperature and humidity drops. It happens just due to the combination of materials.

Thus, the structure of a technical array or engineering board provides three layers:

  • Basis Basis: Moisture-resistant Birch Plywood I or Extra. Thickness can be 6-16 mm depending on the class and value of the material. The perimeter necessarily shares (castle compounds) of one of three types are made. It can be a click type latch, swine-groove knit compounds or puzzle.
  • Upper decorative layer - sections of solid wood thickness from 2.5 to 7 mm thick. From the layer thickness will depend on the amount of possible restations of the mounted floor. If it is 5 mm and more, then about 4-5 permissions are allowed.
  • Protective layer that is applied over wood. It may be varnish or mixtures based on waxes and oils. It is this protective layer that allows you to experiment with the appearance and texture of the coating, change or enhance the shade of natural wood, add additional subteps, enhance the shine.

Advantages and disadvantages of engineering board

Engineering board can be used in elite, exclusive interiors, as well as in premises with pedestrian loads above average. The reason for such versatility and in demand is the main advantages of the material, among which:

1. Increased geometric stability: The risk of deformation of the slats over time is minimal, even if the indoors there will be drops of temperature or humidity (of course, the engineering board cannot be used on unheated dachas or in the bathrooms, but it is suitable for the "warm floor" system).

2. Large selection of length formats, width and thickness Thanks to which you can experiment with the calculation methods and even create a "monolithic" floor in a large room with a base drops in height.

3. Designer variability. You can choose not only the wood breed, but also the type of the upper protective coating, as well as the processing method. Among the popular technologies - livestock, brashing, smoking and making.

4. Possibility of recovery (multiple surface grinding) or local restoration when small damage appears.

5. Durability. The service life of the engineering board varies from 20 to 40 years.

6. A variety of installation methods. Especially for this coverage, several technologies have been developed, including a locking module module or mounted mounted. A combined method of laying is also practiced. You can also experiment with the calculation schemes: the boards fall on a classic deck or any curly method, including a Christmas tree or squares.

Engineering board as high quality material fully justifies its value, which many consider a disadvantage. Of the minuses, it is also worth noting a rather complicated styling process, but in most cases, home craftsmen can cope with installation.

Technology laying. Mounting Rules Engineering Board

As mentioned, there are several technologies for laying such a coating. This is glue, combined and floating. Different types of coatings are suitable as a basis for work for work, including a concrete screed, chipboard, OSB, plywood or wood.

Special polymer compounds are used to glue the engineering board to the prepared base. It is best - on a polyurethane basis, as they have the necessary moisture resistance.

The works are carried out as follows: a special perforated substrate is glued to the pure projected base. Then the holes in the substrate are filled with glue, and the coating (starting from the wall) is fixed. Previously need to calculate the layout according to the scheme.

Combined method implies the use of glue and fasteners. The material is glued with a polymer mixture, as in the previous case, and additionally fixed with self-draws. This is the most reliable way.

It is also possible to lay a "floating" method (but only if the engineering board is initially made with a click lock connection). For such technology, it is not recommended to choose a board with a length of more than 2.2 meters: with longer modules, the master will be inconvenient. The assembly of the floor covering in this case resembles the laying of the laminate: the board does not communicate with the base.

It seems that the cost of material in this case will be lower, however, consider that if necessary, it will take very expensive equipment, which is not far from the wizard. Also in this case, it will takes the creation of compensatory seams around the perimeter to level the expansion and compression during temperature drops.

For many years, the favorite flooring for most people was only laminate, tile and linoleum, but various new items appear on the market of finishing materials. And some of these new products are fairly quickly included. For example, bulk floors moved slightly laminate and linoleum from leading positions. Also, such a type of flooring as an engineering board appeared. This is a new type of finishing material, and therefore it is still known to anyone. So what is an engineering board for the floor? Today we will find out.

What is the gear engineering board?

What is the gear engineering board?

Photo of engineering board

Photo of engineering board

What is the gear engineering board?

Engineering board is a novelty in the field of flooring, a special look, resembling a parquet that has a lot of advantages, if you compare it with a conventional tree. But at the same time, the externally material has a lot in common with massive wood. At the same time, on its operational qualities, such a board exceeds the coating of a natural tree. This is a find for any interior, because wooden floors look equally well in almost any style.

Engineering board characteristics

Engineering board characteristics

Engineering parquet board - what is it?

Engineering parquet board - what is it?

On a note! Interestingly, this type of flooring can be found so far only in Russia - in Western catalogs, especially - apartments, find the engineering board can hardly succeed. Abroad is used very similar by properties. Material is a two-layer parquet board, which has significant differences from a regular parquet.

Engineering board

Engineering board

Engineering cloth boards in context

Engineering cloth boards in context

Like a laminate, the engineering board has a structure consisting of several layers.

  1. Budget Nizhny Made from ordinary plywood, several sheets of which are glued together with each other. At the same time, the direction of the fibers will be alternate, due to which the material acquires increased strength and is protected from deformation in length / width. Sometimes this layer is made of veneer. Its (layer) can still be called the base.
  2. Dear Upper which is made from the wood of valuable rocks. As a rule, it is American, oak or ash walnut. The thickness of the layer is usually about 4 mm - it is enough to ensure that the coating has resistant to external influences and wear.
Engineering board Goodwin Oak Kalahari

Engineering board Goodwin Oak Kalahari

On a note! By the way, 25% of the board composition is valuable wood, and 75% - plywood. The use of plywood was necessary in order to make the material as low as possible at high strength, durability and decorativeness.

Engineering Oak Board, 21 mm

Engineering Oak Board, 21 mm

Engineering board is one of the strongest types of flooring, so now enjoys a fairly great demand. Most often it is used to finish the floor inside the residential premises, and is also used to cover the warm floors. Interestingly, the engineering board is attached to the base (rough floor) almost always with the help of glue. This is due to the fact that the material may be breached.

Engineering board has high strength

Engineering board has high strength

What is the difference between an engineering board from parquet?

This is a question of beginner masters, as well as those who decide to make repairs indoors on their own. To understand what the differences between the two materials are to be familiar with their device and features. Does not fit to find out what is better - a parquet or inspected in the article by an engineering board?

Parquet board or engineering

Parquet board or engineering?

Features of parquet floors

A parquet board is a familiar view of the floor covering, consisting of three-layer wood planks. At the same time, in 90% of cases, layers relative to each other are located so that the direction of fibers they have perpendicular. This allows you to achieve high strength of the product and resistance to external factors. Between itself, the planks are connected by lock connections.

Parquet board

Parquet board

The main feature of the parquet is its structure. Consider in more detail all three layers.

  1. External or front layer It is represented by any valuable woody rock and has a thickness of about 1-4 mm. The surface of the layer can be toned, saturated with oils, is covered with varnish - the latter is needed in order to maximize the panel outside of moisture exposure and increase wear resistance.
  2. Middle Parquet Board - These are perpendicularly laid small racks with a thickness of about 8-9 mm, made from inexpensive wood of coniferous trees. It is the central part of the plank and is equipped with the same compound-lock, which will fasten the bar with each other.
  3. bottom layer Made of wood, most often - coniferous, also not distinguished by a high price. The thickness of the layer is about 1.5 mm.
Section Engineering Board

Parquet floorboard

On a note! Sometimes the bottom layer of the parquet board can be represented by a veneer, and the middle layer - fir or pine. The front in any case is made of valuable wood species.

Paul, covered with parquet, reliable and beautiful. Castle connections between individual straps are quite durable and do not allow the tree to get out, because of which the coating deformation rarely occurs.

Parquet board BEFAG Oak Royal

Parquet board BEFAG Oak Royal

If you know how to wash the parquet floor and how to care for him, you can make sure that the material may well turn out of the capricious into practical and long delight the owners with their beauty. More detail about leaving Read here.

Advantages and disadvantages

Like any other flooring, a parquet board has its own advantages and disadvantages.

Parquet Board has a lot of advantages

Parquet Board has a lot of advantages

Pluses of this finishing material .

  1. The gluing to the rough floor is not required, since all layers within each plank are mutually perpendicular, due to which it is possible to pay off the internal voltage, to avoid curvature and deformation of the material.
  2. Laying parquet boards without glue costs much cheaper (about 6 times) than glue installation of the engineering board (in the absence of castle connections).
  3. Parquet easy to disassemble and collect, which will allow you to pick up the floor covering with you even in the case of moving (if necessary).
  4. Laying the parquet board is available to everyone - it can be done with their own hands.
Floor Floor Parquet Board

Floor Floor Parquet Board

Cons parquet board .

  1. With sharp fluctuations in moisture, the inner layer of the parquet board can collapse. It is especially true for a cheap material, in the manufacture of which low-quality glue compositions were used.
  2. The thickness of the parquet board is quite large - up to 1.4-1.5 cm. Therefore, such a coating is difficult to combine height with another.
  3. Parquet can not be used if a warm floor system is laid.
  4. In the doorways, on the joints of the two types of coatings, thresholds are necessarily used, since the material does not fit on the glue.
  5. There is no possibility to lay a parquet board, except for deck laying.
  6. If the parquet is laid by a floating way, then it is possible to grind it only by expensive equipment.
Aged parquet board in the interior

Aged parquet board in the interior

Parquet board - laying

Parquet board - laying

Features engineering board

The structure of the engineering board was considered in detail above, so in the section we will discuss the specific features of this type of floor covering; So, the main differences of the engineering board from the parquet are as follows:

  • Paul from such a material can be repeatedly covered with varnish;
  • Engineering board is often used as a finish finish for a warm floor;
  • indoors can be marked fluctuations in temperature and humidity, but these factors are not reflected negatively on the material;
  • The engineering board is usually only 2 layers instead of 3.
Engineering board in the interior

Engineering board in the interior

The base of the engineering board is moisture-resistant plywood from birch, the upper part is a plank from a natural expensive tree. Modern lamellas are connected throughout the lock connection or the Schip-groove. In this case, the advantage should be given to the first embodiment, since in this case, you can not use glue compositions to help connect the coating with a draft floor. Due to this, the floor can be easily dismantled if necessary, in contrast to the glued one. However, there was no previously lock connection for engineering boards.

Construction of a two-layer engineering board on a plywood basis

Construction of a two-layer engineering board on a plywood basis

Engineering board may have 3 layers. In this case, its main difference from the parquet is the absence of a breakfast. The bar consists entirely of solid wood sheets. In this case, the second layer is necessarily located perpendicular to the first. Interestingly, individual models of the engineering board base, as well as the outer layer, can be made of wood of valuable rocks.

Three-layer engineering board

Three-layer engineering board

Pros and cons of engineering board

Just like the boarding board, the engineering has its pros and cons, which should be found before deciding, acquire this type of flooring or not.

Engineering board Fine Art Oak Oxford White

Engineering board Fine Art Oak Oxford White

Stylish flooring

Stylish flooring

Advantages of engineering board .

  1. This type of coating has a unique stability against geometry, if compared with other types of floor coatings made using wood.
  2. In the coating of this boards, the slots appear less often, it practically does not respond to changes in humidity conditions.
  3. There is no need to use the freezers if the installation of the engineering board is made on glue. At the same time, regardless of the structure and construction, such floors have good sound insulation. By the way, than elastic glue, the better the coating copes with the absorption of sounds.
  4. Engineering board is quite thin compared to parquet material. It can also have different thickness, depending on the model.
  5. The material can be used for mounting the coating over the warm floor.
  6. Visually, the floor covering from this material does not differ from the floor made from the wood array.
  7. We can lay the coating pattern - for example, squares, a Christmas tree, decorate decorative inserts, etc.
Engineering board for sex a lot of advantages

Engineering board for sex a lot of advantages

Disadvantages of engineering boards like floor covering .

  1. The material is inclined to deformation, if not fixed on glue.
  2. It is a fairly expensive material.
  3. Installation of engineering board is more complicated than parquet.
  4. Covering from this material to collect or disassemble.
  5. Finally, you can easily run into fake, purchasing material in an untested store.
The laid coating cannot be disassembled

The laid coating cannot be disassembled

What is better - parquet board or engineering?

As you can note, reading the above information, parquet and engineering boards have a lot of general and at the same time there are important differences. Rodinitis them between themselves the external similarity of the finished coating with a natural array of wood. Also both types of finishes are safe for human health, and the sun do not burn out.

In general, each wave to decide which material is best used in one way or another. At the same time, it is convenient to analyze the upcoming repair work and is then determined with the choice.

Laying engineering board on the floor

Laying engineering board on the floor

Engineering board

Engineering board

In this example, the type of connection - Schip-groove

In this example, the type of connection - Schip-groove

Example of finished coating

Example of finished coating

Criteria for choosing brand

Before the installation of the engineering board is studied, the necessary material should be purchased. To navigate throughout the variety of products and manufacturing companies, it is possible according to the reviews of those who have already enjoyed the products of this or that firm. Also, some information about the most popular manufacturers is given in the table.

Rating of the best manufacturers

Hajnowka.

Polish brand, whose products are considered one of the best and is known worldwide. The highest quality, environmental friendliness, beauty inherent in the HAJNOWKA engineering board made it possible to take a leading position in the market. Interestingly, in the line of models there are unique forms that are not found from other manufacturers is the merit of professional designers. Material thickness - 15 mm.

pros

  • high quality;
  • big palette of colors;
  • Two wood species (oak and ash) are used;
  • The average price category.

Engineering board Hajnowka.

Boen.

A fairly well-known company, the production of which is conducted in Lithuania and Germany, as well as in other countries of the world, except Russia. The engineering board of this company refers to the category of premium products, has a lot of shades.

pros

  • Environmentally friendly product;
  • Boards are represented by three classes;
  • High resistance to wear, and complete safety of use.

Engineering board Boen.

Panaget.

Plank from France, made on the basis of plywood. Methods of compounds of the planks are also present, depending on the model - and the castle, and the spike-groove. It has an additional stabilizer.

pros

  • material is environmentally safe;
  • Warranty from the manufacturer for over 20 years.

Minuses

  • high price;
  • Stacking better trust professionals.

Engineering board Panaget.

Goodwin

The German-Chinese brand produced by which products have their own characteristics. For example, a small length of the slats is 120 cm, although in general the lamellas are produced up to 2 m long.

pros

  • The base is birch plywood;
  • The top layer is one-piece wood of Russian oak or American walnut with a thickness of 4 mm;
  • low cost.

Minuses

  • In some parties, the boards may differ in shades.

Engineering board Goodwin

Features Engineering Board

It's time to familiarize yourself with how the engineering board laying. Instructions will help.

Step 1. Careful cleaning of the rough concrete floor from garbage is performed.

Preparation of the foundation

Preparation of the foundation

Step 2. The surface of the floor is grounded with two-component epoxy primer - it is necessarily a good area near the walls, as well as the entire surface of the entire surface. It is necessary to begin to apply primer from the opposite way out of the side room. Big surfaces are more convenient to cover using roller.

Applying primer brush

Applying primer brush

The primer is applied with roller

The primer is applied with roller

Step 3. The surface is well dry.

Next, you need to wait for the surface drying

Next, you need to wait for the surface drying

Step 4. A special substrate with perforation is placed on the floor.

Laying the substrate with perforation

Laying the substrate with perforation

Stacking process

Stacking process

Step 5. The glue composition is applied along the wall where the engineering board will begin.

Applying glue along the wall

Applying glue along the wall

Bostik KPA, durable to shift, universal for use

Bostik KPA, durable to shift, universal for use

Step 6. Also, the adhesive composition is applied to perforation holes.

Glue is applied in the substrate hole

Glue is applied in the substrate hole

Another photo of the process

Another photo of the process

Attention! It does not need to miss all the holes at once - this is done in stages, as the flooring is styled.

Step 7. Along the wall on the adhesive applied in advance and the laid substrate close to the wall bowls the first panel.

The first board is stacked along the wall

The first board is stacked along the wall

Step 8. The entire first row is located close to the wall.

Laying of the first row

Laying of the first row

Step 9. The installation of the second row is carried out. The panels are stacked very tightly to each other, join the fastening system.

Laying the second series

Laying of the second row

Engineering boards fit closely

Engineering boards fit closely

Step 10. As needed glue is applied to subsequent holes. The laying of the coating further.

Glue is applied to the subsequent holes of the substrate

Glue is applied to the subsequent holes of the substrate

Step 11. For a more dense connection of the layers of each other, a hammer may be required, which panels neatly be lit to each other. Similarly, the entire floor is separated.

When installing the hammer is used

When installing the hammer is used

Video - engineering board laying

Using an engineering board - one of the best ways to make a beautiful, reminiscent of the present massive tree flooring. More and more people make their choice in favor of this material. In any case, the advantages of the engineering board are quite a lot, and therefore it can become an excellent alternative to laminate and other types of coverage.

Leave a Reply